View KS8721B11_2270358.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

march 2006 1 m9999-030106 ks8721b/bt ks8721b/bt 2.5v 10/100bastx/fx mii physical layer transceiver rev. 2.3 general description operating at 2.5 volts to meet low voltage and low power requirements, the ks8721b/bt is a 10baset/100basetx/fx physical layer transceiver, which provides an mii to transmit and receive data. it contains the 10baset physical medium attachment (pma), physical medium dependent (pmd), and physical coding sub-layer (pcs) functions. moreover, the ks8721b/bt has on-chip 10baset output ? ltering, which eliminates the need for external ? lters and allows a single set of line magnetics to be used to meet requirements for both 100basetx and 10baset. the ks8721b/bt can automatically con? gure itself for 100 or 10 mbps and full or half duplex operation, using on-chip auto-negotiation algorithm. it is an ideal choice of physical layer transceiver for 100basetx/10baset applications. data sheets and support documentation can be found on micrels web site at www.micrel.com. features ? single chip 100basetx/100basefx/10baset physical layer solution ? 2.5v cmos design, power consumption <200mw (ex- cluding output driver current ) ? fully compliant to ieee 802.3u standard ? supports media independent interface (mii) and reduced mii (rmii) ? supports 10baset, 100basetx and 100basefx with far_end_fault detection ? supports power down mode and power saving mode ? con? gurable through mii serial management ports or via external control pins ? supports auto-negotiation and manual selection for 10/100mbps speed and full/half-duplex mode ? on-chip built-in analog front end ? ltering for both 100ba- setx and 10baset micrel, inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel + 1 (408) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com functional diagram 10/100 pulse shaper nrz/nrzi mlt3 encoder parallel/serial manchester encoder 4b/5b encoder scrambler parallel/serial transmitter tx+ tx- adaptive eq base line wander correction mlt3 decoder nrzi/nrz clock recovery 4b/5b decoder descrambler serial/parallel auto negotiation 10baset receiver manchester decoder serial/parallel pll led driver mii/rmii registers and controller interface rx- rx+ xi xo spd fdx col link power down or saving pwrdwn rxc txd3 txd0 txd1 txd2 rxd3 txen txc txer mdc mdio col crs rxer rxd0 rxd1 rxd2 rxdv
ks8721b/bt micrel, inc. m9999-030106 2 march 2006 features (continued) ? led outputs for link, activity, full/half duplex, collision and speed ? supports back to back, fx to tx for media converter applications ? supports mdi/mdi-x auto crossover ? 2.5v/3.3v tolerance on i/o ? commercial temperature range: 0c to +70c ? industrial temperature range: C40c to +85c ? available in 48-pin ssop and tqfp ordering information part number temperature package standard pb-free ks8721b ksz8721b 0c to +70c 48-pin ssop ks8721bt ksz8721bt 0c to +70c 48-pin tqfp ksz8721bi C40c to +85c 48-pin ssop
march 2006 3 m9999-030106 ks8721b/bt micrel, inc. revision history revision date summary of changes 1.0 2/29/02 document origination (preliminary) 2.0 4/01/02 update timing spec from page 33 to page 37 change revision id from 1000 to 1001 add new control register bit, control register 0 bit 0, to control transmit enable/disable add 8h register map on the table editorial change on fxsd/fxen pin34 change on duplex pin38 0=half and 1=full duplex change on the 10bt mii transmit timing 1.0us to 2.5us and tlat 2.5us to 4bt add the test description mode on pin26 2.1 1/31/03 add part number ordering information & remove pinout diagram edited pin description on the io cloumn change the company logo, disclaimer, & contact info editorial changes on stapping option description change on register0h bit0, 1=disable and 0=enable add remote fault register4h bit13. add normal operating condition table & thermal data for ssop48 table add reset timing table & transformer lists add 48 tqfp pinout diagram & rmii ac charateristics add ordering info for 48 pin tqfp package, ks8721b/bti industrial temperature, ksy8721b/ksy8721bt environmentally friendly part number 2.2 8/29/03 change part number from ks8721b to ks8721b/bt. change ordering info. from ksy to ksz for lead free. change pin name from rmii_lpbk to rmii_btb convert to new format. 2.3 1/24/04 mdio pull-up resistor value changed to 4.7k. added note on strapping option pins. updated bit 1b.0 - 1b.7 to self-clearing. updated electrical characteristic. updated bit 1f4:2 to resetted. added additional magnetics to quali? ed transformer. added reset reference circuit. 2.3 3/16/05 added rmii timing speci? cation. 1.0 2/29/02 document origination (preliminary) 2.0 4/01/02 update timing spec from page 33 to page 37 change revision id from 1000 to 1001 add new control register bit, control register 0 bit 0, to control transmit enable/disable add 8h register map on the table editorial change on fxsd/fxen pin34 change on duplex pin38 0=half and 1=full duplex change on the 10bt mii transmit timing 1.0us to 2.5us and tlat 2.5us to 4bt add the test description mode on pin26 2.1 1/31/03 add part number ordering information & remove pinout diagram edited pin description on the io cloumn change the company logo, disclaimer, & contact info editorial changes on stapping option description change on register0h bit0, 1=disable and 0=enable add remote fault register4h bit13. add normal operating condition table & thermal data for ssop48 table add reset timing table & transformer lists add 48 tqfp pinout diagram & rmii ac charateristics add ordering info for 48 pin tqfp package, ks8721b/bti industrial temperature, ksy8721b/ksy8721bt environmentally friendly part number 2.2 8/29/03 change part number from ks8721b to ks8721b/bt. change ordering info. from ksy to ksz for lead free. change pin name from rmii_lpbk to rmii_btb convert to new format. 2.3 1/24/04 mdio pull-up resistor value changed to 4.7k. added note on strapping option pins. updated bit 1b.0 - 1b.7 to self-clearing. updated electrical characteristic. updated bit 1f4:2 to resetted. added additional magnetics to quali? ed transformer. added reset reference circuit. 2.3 3/16/05 added rmii timing speci? cation. revision date summary of changes 1.0 2/29/02 document origination (preliminary) 2.0 4/01/02 update timing spec from page 33 to page 37 change revision id from 1000 to 1001 add new control register bit, control register 0 bit 0, to control transmit enable/disable add 8h register map on the table editorial change on fxsd/fxen pin34 change on duplex pin38 0=half and 1=full duplex change on the 10bt mii transmit timing 1.0us to 2.5us and tlat 2.5us to 4bt add the test description mode on pin26 2.1 1/31/03 add part number ordering information & remove pinout diagram edited pin description on the io cloumn change the company logo, disclaimer, & contact info editorial changes on stapping option description change on register0h bit0, 1=disable and 0=enable add remote fault register4h bit13. add normal operating condition table & thermal data for ssop48 table add reset timing table & transformer lists add 48 tqfp pinout diagram & rmii ac charateristics add ordering info for 48 pin tqfp package, ks8721b/bti industrial temperature, ksy8721b/ksy8721bt environmentally friendly part number 2.2 8/29/03 change part number from ks8721b to ks8721b/bt. change ordering info. from ksy to ksz for lead free. change pin name from rmii_lpbk to rmii_btb convert to new format. 2.3 1/24/04 mdio pull-up resistor value changed to 4.7k. added note on strapping option pins. updated bit 1b.0 - 1b.7 to self-clearing. updated electrical characteristic. updated bit 1f4:2 to resetted. added additional magnetics to quali? ed transformer. added reset reference circuit. 2.3 3/16/05 added rmii timing speci? cation. revision date summary of changes 1.0 2/29/02 document origination (preliminary) 2.0 4/01/02 update timing spec from page 33 to page 37 change revision id from 1000 to 1001 add new control register bit, control register 0 bit 0, to control transmit enable/disable add 8h register map on the table editorial change on fxsd/fxen pin34 change on duplex pin38 0=half and 1=full duplex change on the 10bt mii transmit timing 1.0us to 2.5us and tlat 2.5us to 4bt add the test description mode on pin26 2.1 1/31/03 add part number ordering information & remove pinout diagram edited pin description on the io cloumn change the company logo, disclaimer, & contact info editorial changes on stapping option description change on register0h bit0, 1=disable and 0=enable add remote fault register4h bit13. add normal operating condition table & thermal data for ssop48 table add reset timing table & transformer lists add 48 tqfp pinout diagram & rmii ac charateristics add ordering info for 48 pin tqfp package, ks8721b/bti industrial temperature, ksy8721b/ksy8721bt environmentally friendly part number 2.2 8/29/03 change part number from ks8721b to ks8721b/bt. change ordering info. from ksy to ksz for lead free. change pin name from rmii_lpbk to rmii_btb convert to new format. 2.3 1/24/04 mdio pull-up resistor value changed to 4.7k. added note on strapping option pins. updated bit 1b.0 - 1b.7 to self-clearing. updated electrical characteristic. updated bit 1f4:2 to resetted. added additional magnetics to quali? ed transformer. added reset reference circuit. 2.3 3/16/05 added rmii timing speci? cation.
ks8721b/bt micrel, inc. m9999-030106 4 march 2006 table of contents pin description ............................................................................................................................................................. 6 strapping option ........................................................................................................................................................... 9 pin con? guration ........................................................................................................................................................ 10 introduction ............................................................................................................................................................ 11 100basetx transmit ............................................................................................................................................. 11 100basetx receive ............................................................................................................................................. 11 pll clock synthesizer .......................................................................................................................................... pll clock synthesizer ............................................................................................ .............................................. pll clock synthesizer 11 scrambler/de-scrambler (100basetx only) ......................................................................................................... 11 10baset transmit ................................................................................................................................................. 11 10baset receive .................................................................................................................................................. 11 sqe and jabber function (10base only) .............................................................................................................. 11 auto-negotiation ................................................................................................................................................... 11 mii management interface .................................................................................................................................... 12 mii data interface .................................................................................................................................................. 12 transmit clock .............................................................................................................................................. 12 receive clock ............................................................................................................................................... 12 transmit enable ............................................................................................................................................ 12 receive data valid ........................................................................................................................................ 12 error signals .................................................................................................................................................. 12 carrier sense ................................................................................................................................................ 12 collision ......................................................................................................................................................... 13 rmii signal de? nition ............................................................................................................................................ 13 reference clock .................................................................................................................................................... 13 carrier sense/receive data valid ......................................................................................................................... 13 receive data ......................................................................................................................................................... 13 transmit enable .................................................................................................................................................... 13 transmit data ........................................................................................................................................................ 14 collision detection ................................................................................................................................................ 14 rx_er ............................................................................................................................................................ 14 rmii ac characteristics ........................................................................................................................................ 14 auto crossover (auto mdi/mdi-x) ........................................................................................................................ 15 power management .............................................................................................................................................. 16 100bt fx mode .................................................................................................................................................... 16 media converter option ........................................................................................................................................ 16 register map ............................................................................................................................................................ 17 register 0h: basic conrol ..................................................................................................................................... 17 register 1h: basic status ..................................................................................................................................... 18 register 2h: phy identi? er 1 ................................................................................................................................ 18 register 3h: phy identi? er 2 ................................................................................................................................ 18 register 4h: auto-negotiation advertisement ....................................................................................................... 18 register 5h: auto-negotiation link partner ability ................................................................................................ 18 register 6h: auto-negotiation expansion ............................................................................................................. 19 register 7h: auto-negotiation next page ............................................................................................................. 19 register 8h: link partner next page ability ......................................................................................................... 19 register 15h: rxer counter ............................................................................................................................... register 15h: rxer counter ............................................................................................ ................................... register 15h: rxer counter 20 register 1bh: interrupt control/status register ................................................................................................... register 1bh: interrupt control/status register ............................................................................................ ....... register 1bh: interrupt control/status register 20 register 1fh: 100basetx phy controller ............................................................................................................ register 1fh: 100basetx phy controller ............................................................................................ ................ register 1fh: 100basetx phy controller 20
march 2006 5 m9999-030106 ks8721b/bt micrel, inc. absolute maximum ratings ....................................................................................................................................... 22 operating ratings ....................................................................................................................................................... 22 electrical characteristics ........................................................................................................................................... 22 timing diagrams ......................................................................................................................................................... 24 selection of isolation transformers .......................................................................................................................... 30 selection of reference crystals ................................................................................................................................ 30 package outline and dimensions ............................................................................................................................. 31
ks8721b/bt micrel, inc. m9999-030106 6 march 2006 pin description pin number pin name type (note 1) (note 1) pin function 1 mdio i/o management interface (mii) data i/o: this pin requires an external 4.7k pull-up resistor. 2 mdc i management interface (mii) clock input: this pin is synchronous to the mdio data interface 3 rxd3/ ipd/o mii receive data output: rxd [3..0], these bits are synchronous with rxclk. phyad1 when rxdv is asserted, rxd [3..0] presents valid data to mac through the mii. rxd [3..0] is invalid when rxdv is de-asserted. the pull-up/pull-down value is latched as phyaddr [1] during reset. see strapping options section for strapping options section for strapping options details. 4 rxd2/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [2] phyad2 during reset. see strapping options section for details. strapping options section for details. strapping options 5 rxd1/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [3] phyad3 during reset. see strapping options section for details. strapping options section for details. strapping options 6 rxd0/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [4] phyad4 during reset. see strapping options section for details. strapping options section for details. strapping options 7 vddio pwr digital io 2.5 /3.3v tolerance power supply. 8 gnd gnd ground. 9 rxdv/ ipd/o mii receive data valid output: the pull-up/pull-down value is latched as crsdv/ pcs_lpbk during reset. see strapping options section for details. strapping options section for details. strapping options pcs_lpbk 10 rxc o mii receive clock output: operating at 25mhz = 100mbps, 2.5mhz = 10mbps. 11 rxer/iso ipd/o mii receive error output: the pull-up/pull-down value is latched as isolate during reset. see strapping options section for details. strapping options section for details. strapping options 12 gnd gnd ground. 13 vddc pwr digital core 2.5v only power supply. 14 txer ipd mii transmit error input. 15 txc/ ipu/o mii transmit clock output: rmii reference clock input. refclk 16 txen ipd mii transmit enable input 17 txd0 ipd mii transmit data input 18 txd1 ipd mii transmit data input 19 txd2 ipd mii transmit data input 20 txd3 ipd mii transmit data input 21 col/rmii ipd/o mii collision detect output: the pull-up/pull-down value is latched as rmii select during reset. see strapping options section for details. strapping options section for details. strapping options 24 vddio pwr digital io 2.5/3.3v tolerance power supply. note 1. pwr = power supply gnd = ground i = input o = output i/o = bi-directional gnd = ground ipu = input w/ internal pull-up ipd = input w/ internal pull-down ipd/o = input w/ internal pull-down during reset, output pin otherwise ipu/o = input w/ internal pull-up during reset, output pin otherwise pu = strap pin pull-up pd = strap pin pull-down nc = no connect 1 mdio i/o management interface (mii) data i/o: this pin requires an external 4.7k pull-up resistor. 2 mdc i management interface (mii) clock input: this pin is synchronous to the mdio data interface 3 rxd3/ ipd/o mii receive data output: rxd [3..0], these bits are synchronous with rxclk. phyad1 when rxdv is asserted, rxd [3..0] presents valid data to mac through the mii. rxd [3..0] is invalid when rxdv is de-asserted. the pull-up/pull-down value is latched as phyaddr [1] during reset. see details. 4 rxd2/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [2] phyad2 during reset. see 5 rxd1/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [3] phyad3 during reset. see 6 rxd0/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [4] phyad4 during reset. see 7 vddio pwr digital io 2.5 /3.3v tolerance power supply. 8 gnd gnd ground. 9 rxdv/ ipd/o mii receive data valid output: the pull-up/pull-down value is latched as crsdv/ pcs_lpbk during reset. see pcs_lpbk 10 rxc o mii receive clock output: operating at 25mhz = 100mbps, 2.5mhz = 10mbps. 11 rxer/iso ipd/o mii receive error output: the pull-up/pull-down value is latched as isolate during reset. see 12 gnd gnd ground. 13 vddc pwr digital core 2.5v only power supply. 14 txer ipd mii transmit error input. 15 txc/ ipu/o mii transmit clock output: rmii reference clock input. refclk 16 txen ipd mii transmit enable input 17 txd0 ipd mii transmit data input 18 txd1 ipd mii transmit data input 19 txd2 ipd mii transmit data input 20 txd3 ipd mii transmit data input 21 col/rmii ipd/o mii collision detect output: the pull-up/pull-down value is latched as rmii select during reset. see 24 vddio pwr digital io 2.5/3.3v tolerance power supply. pin number pin name type 1 mdio i/o management interface (mii) data i/o: this pin requires an external 4.7k pull-up resistor. 2 mdc i management interface (mii) clock input: this pin is synchronous to the mdio data interface 3 rxd3/ ipd/o mii receive data output: rxd [3..0], these bits are synchronous with rxclk. phyad1 when rxdv is asserted, rxd [3..0] presents valid data to mac through the mii. rxd [3..0] is invalid when rxdv is de-asserted. the pull-up/pull-down value is latched as phyaddr [1] during reset. see details. 4 rxd2/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [2] phyad2 during reset. see 5 rxd1/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [3] phyad3 during reset. see 6 rxd0/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [4] phyad4 during reset. see 7 vddio pwr digital io 2.5 /3.3v tolerance power supply. 8 gnd gnd ground. 9 rxdv/ ipd/o mii receive data valid output: the pull-up/pull-down value is latched as crsdv/ pcs_lpbk during reset. see pcs_lpbk 10 rxc o mii receive clock output: operating at 25mhz = 100mbps, 2.5mhz = 10mbps. 11 rxer/iso ipd/o mii receive error output: the pull-up/pull-down value is latched as isolate during reset. see 12 gnd gnd ground. 13 vddc pwr digital core 2.5v only power supply. 14 txer ipd mii transmit error input. 15 txc/ ipu/o mii transmit clock output: rmii reference clock input. refclk 16 txen ipd mii transmit enable input 17 txd0 ipd mii transmit data input 18 txd1 ipd mii transmit data input 19 txd2 ipd mii transmit data input 20 txd3 ipd mii transmit data input 21 col/rmii ipd/o mii collision detect output: the pull-up/pull-down value is latched as rmii select during reset. see 24 vddio pwr digital io 2.5/3.3v tolerance power supply. pin number pin name type 1 mdio i/o management interface (mii) data i/o: this pin requires an external 4.7k pull-up resistor. 2 mdc i management interface (mii) clock input: this pin is synchronous to the mdio data interface 3 rxd3/ ipd/o mii receive data output: rxd [3..0], these bits are synchronous with rxclk. phyad1 when rxdv is asserted, rxd [3..0] presents valid data to mac through the mii. rxd [3..0] is invalid when rxdv is de-asserted. the pull-up/pull-down value is latched as phyaddr [1] during reset. see details. 4 rxd2/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [2] phyad2 during reset. see 5 rxd1/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [3] phyad3 during reset. see 6 rxd0/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [4] phyad4 during reset. see 7 vddio pwr digital io 2.5 /3.3v tolerance power supply. 8 gnd gnd ground. 9 rxdv/ ipd/o mii receive data valid output: the pull-up/pull-down value is latched as crsdv/ pcs_lpbk during reset. see pcs_lpbk 10 rxc o mii receive clock output: operating at 25mhz = 100mbps, 2.5mhz = 10mbps. 11 rxer/iso ipd/o mii receive error output: the pull-up/pull-down value is latched as isolate during reset. see 12 gnd gnd ground. 13 vddc pwr digital core 2.5v only power supply. 14 txer ipd mii transmit error input. 15 txc/ ipu/o mii transmit clock output: rmii reference clock input. 16 txen ipd mii transmit enable input 17 txd0 ipd mii transmit data input 18 txd1 ipd mii transmit data input 19 txd2 ipd mii transmit data input 20 txd3 ipd mii transmit data input 21 col/rmii ipd/o mii collision detect output: the pull-up/pull-down value is latched as rmii select during reset. see 24 vddio pwr digital io 2.5/3.3v tolerance power supply. pin function 1 mdio i/o management interface (mii) data i/o: this pin requires an external 4.7k pull-up resistor. 2 mdc i management interface (mii) clock input: this pin is synchronous to the mdio data interface 3 rxd3/ ipd/o mii receive data output: rxd [3..0], these bits are synchronous with rxclk. phyad1 when rxdv is asserted, rxd [3..0] presents valid data to mac through the mii. rxd [3..0] is invalid when rxdv is de-asserted. the pull-up/pull-down value is latched as phyaddr [1] during reset. see details. 4 rxd2/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [2] phyad2 during reset. see 5 rxd1/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [3] phyad3 during reset. see 6 rxd0/ ipd/o mii receive data output: the pull-up/pull-down value is latched as phyaddr [4] phyad4 during reset. see 7 vddio pwr digital io 2.5 /3.3v tolerance power supply. 8 gnd gnd ground. 9 rxdv/ ipd/o mii receive data valid output: the pull-up/pull-down value is latched as crsdv/ pcs_lpbk during reset. see pcs_lpbk 10 rxc o mii receive clock output: operating at 25mhz = 100mbps, 2.5mhz = 10mbps. 11 rxer/iso ipd/o mii receive error output: the pull-up/pull-down value is latched as isolate during reset. see 12 gnd gnd ground. 13 vddc pwr digital core 2.5v only power supply. 14 txer ipd mii transmit error input. 15 txc/ ipu/o mii transmit clock output: rmii reference clock input. 16 txen ipd mii transmit enable input 17 txd0 ipd mii transmit data input 18 txd1 ipd mii transmit data input 19 txd2 ipd mii transmit data input 20 txd3 ipd mii transmit data input 21 col/rmii ipd/o mii collision detect output: the pull-up/pull-down value is latched as rmii select during reset. see 24 vddio pwr digital io 2.5/3.3v tolerance power supply.
march 2006 7 m9999-030106 ks8721b/bt micrel, inc. pin number pin name type (note 1) pin function 25 int#/ ipu/o management interface (mii) interrupt out: latched as phyad[0] during power up phyad0 /reset. see strapping options section for details. strapping options section for details. strapping options 22 crs/ ipd/o mii carrier sense output: the pull-up/pull-down value is latched as rmii btb rmii_btb during reset when rmii mode is selected. see strapping options section strapping options section strapping options for details. 23 gnd gnd ground. 26 led0/test ipu/o link/activity led output: lnk/act pin state led de? nition no link h off link l on act toggle the external pull-down enable test mode and only used for the factory test. 27 led1/ ipu/o speed led output: latched as speed (register 0, bit 13) during power-up/reset. spd100/ see strapping options section for details. strapping options section for details. strapping options nofef speed pin state led de? nition 10bt h off 100bt l on 28 led2/ ipu/o full-duplex led output: latched as duplex (register 0h, bit 8) during power-up/ duplex reset. see strapping options section for details. strapping options section for details. strapping options duplex pin state led de? nition half h off full l on 29 led3/ ipu/o collision led output: latched as aneg_en (register 0h, bit 12) during power-up/ nwayen reset. see strapping options section for details. strapping options section for details. strapping options collison pin state led de? nition no collision h off collision l on 30 pd# ipu power down. 1 = normal operation, 0=power down, active low. 31 vddrx pwr analog 2.5v power supply. 32 rx- i receive input: differential receive input pins for fx, 100basetx or 10baset. 33 rx+ i receive input: differential receive input pin for fx, 100basetx or 10baset. 34 fxsd/fxen ipd/o fiber mode enable / signal detect in fiber mode. if fxen = 0, fx mode is disable. the default is 0. see 100bt fx mode section for more details. 100bt fx mode section for more details. 100bt fx mode 35 gnd gnd ground. 36 gnd gnd ground. note 1. pwr = power supply gnd = ground i = input o = output i/o = bi-directional ipu = input w/ internal pull-up ipd = input w/ internal pull-down ipd/o = input w/ internal pull-down during reset, output pin otherwise ipu/o = input w/ internal pull-up during reset, output pin otherwise pu = strap pin pull-up pd = strap pin pull-down nc = no connect 25 int#/ ipu/o management interface (mii) interrupt out: latched as phyad[0] during power up phyad0 /reset. see 22 crs/ ipd/o mii carrier sense output: the pull-up/pull-down value is latched as rmii btb rmii_btb during reset when rmii mode is selected. see for details. 23 gnd gnd ground. 26 led0/test ipu/o link/activity led output: lnk/act pin state led de? nition no link h off link l on act toggle the external pull-down enable test mode and only used for the factory test. 27 led1/ ipu/o speed led output: latched as speed (register 0, bit 13) during power-up/reset. spd100/ see nofef speed pin state led de? nition 10bt h off 100bt l on 28 led2/ ipu/o full-duplex led output: latched as duplex (register 0h, bit 8) during power-up/ duplex reset. see half h off full l on 29 led3/ ipu/o collision led output: latched as aneg_en (register 0h, bit 12) during power-up/ nwayen reset. see no collision h off collision l on 30 pd# ipu power down. 1 = normal operation, 0=power down, active low. 31 vddrx pwr analog 2.5v power supply. 32 rx- i receive input: differential receive input pins for fx, 100basetx or 10baset. 33 rx+ i receive input: differential receive input pin for fx, 100basetx or 10baset. 34 fxsd/fxen ipd/o fiber mode enable / signal detect in fiber mode. if fxen = 0, fx mode is disable. the default is 0. see 35 gnd gnd ground. 36 gnd gnd ground. pin number pin name type 25 int#/ ipu/o management interface (mii) interrupt out: latched as phyad[0] during power up phyad0 /reset. see 22 crs/ ipd/o mii carrier sense output: the pull-up/pull-down value is latched as rmii btb rmii_btb during reset when rmii mode is selected. see for details. 23 gnd gnd ground. 26 led0/test ipu/o link/activity led output: lnk/act pin state led de? nition no link h off link l on act toggle the external pull-down enable test mode and only used for the factory test. 27 led1/ ipu/o speed led output: latched as speed (register 0, bit 13) during power-up/reset. spd100/ see nofef speed pin state led de? nition 10bt h off 100bt l on 28 led2/ ipu/o full-duplex led output: latched as duplex (register 0h, bit 8) during power-up/ duplex reset. see half h off full l on 29 led3/ ipu/o collision led output: latched as aneg_en (register 0h, bit 12) during power-up/ nwayen reset. see no collision h off collision l on 30 pd# ipu power down. 1 = normal operation, 0=power down, active low. 31 vddrx pwr analog 2.5v power supply. 32 rx- i receive input: differential receive input pins for fx, 100basetx or 10baset. 33 rx+ i receive input: differential receive input pin for fx, 100basetx or 10baset. 34 fxsd/fxen ipd/o fiber mode enable / signal detect in fiber mode. if fxen = 0, fx mode is disable. the default is 0. see 35 gnd gnd ground. 36 gnd gnd ground. pin number pin name type 25 int#/ ipu/o management interface (mii) interrupt out: latched as phyad[0] during power up phyad0 /reset. see 22 crs/ ipd/o mii carrier sense output: the pull-up/pull-down value is latched as rmii btb rmii_btb during reset when rmii mode is selected. see for details. 23 gnd gnd ground. 26 led0/test ipu/o link/activity led output: lnk/act pin state led de? nition no link h off link l on act toggle the external pull-down enable test mode and only used for the factory test. 27 led1/ ipu/o speed led output: latched as speed (register 0, bit 13) during power-up/reset. spd100/ see nofef speed pin state led de? nition 10bt h off 100bt l on 28 led2/ ipu/o full-duplex led output: latched as duplex (register 0h, bit 8) during power-up/ duplex reset. see half h off full l on 29 led3/ ipu/o collision led output: latched as aneg_en (register 0h, bit 12) during power-up/ nwayen reset. see no collision h off collision l on 30 pd# ipu power down. 1 = normal operation, 0=power down, active low. 31 vddrx pwr analog 2.5v power supply. 32 rx- i receive input: differential receive input pins for fx, 100basetx or 10baset. 33 rx+ i receive input: differential receive input pin for fx, 100basetx or 10baset. 34 fxsd/fxen ipd/o fiber mode enable / signal detect in fiber mode. if fxen = 0, fx mode is disable. the default is 0. see 35 gnd gnd ground. 36 gnd gnd ground. pin function 25 int#/ ipu/o management interface (mii) interrupt out: latched as phyad[0] during power up phyad0 /reset. see 22 crs/ ipd/o mii carrier sense output: the pull-up/pull-down value is latched as rmii btb rmii_btb during reset when rmii mode is selected. see for details. 23 gnd gnd ground. 26 led0/test ipu/o link/activity led output: lnk/act pin state led de? nition no link h off link l on act toggle the external pull-down enable test mode and only used for the factory test. 27 led1/ ipu/o speed led output: latched as speed (register 0, bit 13) during power-up/reset. spd100/ see speed pin state led de? nition 10bt h off 100bt l on 28 led2/ ipu/o full-duplex led output: latched as duplex (register 0h, bit 8) during power-up/ duplex reset. see half h off full l on 29 led3/ ipu/o collision led output: latched as aneg_en (register 0h, bit 12) during power-up/ nwayen reset. see no collision h off collision l on 30 pd# ipu power down. 1 = normal operation, 0=power down, active low. 31 vddrx pwr analog 2.5v power supply. 32 rx- i receive input: differential receive input pins for fx, 100basetx or 10baset. 33 rx+ i receive input: differential receive input pin for fx, 100basetx or 10baset. 34 fxsd/fxen ipd/o fiber mode enable / signal detect in fiber mode. if fxen = 0, fx mode is disable. the default is 0. see 35 gnd gnd ground. 36 gnd gnd ground. lnk/act pin state led de? nition no link h off link l on act toggle lnk/act pin state led de? nition no link h off link l on act toggle speed pin state led de? nition 10bt h off 100bt l on speed pin state led de? nition 10bt h off 100bt l on duplex pin state led de? nition half h off full l on duplex pin state led de? nition half h off full l on collison pin state led de? nition no collision h off collision l on collison pin state led de? nition no collision h off collision l on
ks8721b/bt micrel, inc. m9999-030106 8 march 2006 pin number pin name type (note 1) pin function 37 rext i external resistor (6.49k) connects to rext and gndrx. 38 vddrcv pwr analog 2.5v power supply. 39 gnd gnd ground 40 tx- o transmit outputs: differential transmit output for 100basetx/fx or 10baset. 41 tx+ o transmit outputs: differential transmit output for fx, 100basetx/fx or 10baset. 42 vddtx pwr transmitter 2.5v power supply. 43 gnd gnd ground. 44 gnd gnd ground. 45 xo o xtal feedback: used with xi for xtal application. 46 xi i crystal oscillator input: input for a crystal or an external 25mhz clock 47 vddpll pwr analog pll 2.5v power supply. 48 rst# ipu chip reset: active low, minimum of 50s pulse is required note 1. pwr = power supply gnd = ground i = input o = output i/o = bi-directional ipu = input w/ internal pull-up ipd = input w/ internal pull-down ipd/o = input w/ internal pull-down during reset, output pin otherwise ipu/o = input w/ internal pull-up during reset, output pin otherwise pu = strap pin pull-up pd = strap pin pull-down nc = no connect 37 rext i external resistor (6.49k) connects to rext and gndrx. 38 vddrcv pwr analog 2.5v power supply. 39 gnd gnd ground 40 tx- o transmit outputs: differential transmit output for 100basetx/fx or 10baset. 41 tx+ o transmit outputs: differential transmit output for fx, 100basetx/fx or 10baset. 42 vddtx pwr transmitter 2.5v power supply. 43 gnd gnd ground. 44 gnd gnd ground. 45 xo o xtal feedback: used with xi for xtal application. 46 xi i crystal oscillator input: input for a crystal or an external 25mhz clock 47 vddpll pwr analog pll 2.5v power supply. 48 rst# ipu chip reset: active low, minimum of 50s pulse is required pin number pin name type 37 rext i external resistor (6.49k) connects to rext and gndrx. 38 vddrcv pwr analog 2.5v power supply. 39 gnd gnd ground 40 tx- o transmit outputs: differential transmit output for 100basetx/fx or 10baset. 41 tx+ o transmit outputs: differential transmit output for fx, 100basetx/fx or 10baset. 42 vddtx pwr transmitter 2.5v power supply. 43 gnd gnd ground. 44 gnd gnd ground. 45 xo o xtal feedback: used with xi for xtal application. 46 xi i crystal oscillator input: input for a crystal or an external 25mhz clock 47 vddpll pwr analog pll 2.5v power supply. 48 rst# ipu chip reset: active low, minimum of 50s pulse is required pin number pin name type 37 rext i external resistor (6.49k) connects to rext and gndrx. 38 vddrcv pwr analog 2.5v power supply. 39 gnd gnd ground 40 tx- o transmit outputs: differential transmit output for 100basetx/fx or 10baset. 41 tx+ o transmit outputs: differential transmit output for fx, 100basetx/fx or 10baset. 42 vddtx pwr transmitter 2.5v power supply. 43 gnd gnd ground. 44 gnd gnd ground. 45 xo o xtal feedback: used with xi for xtal application. 46 xi i crystal oscillator input: input for a crystal or an external 25mhz clock 47 vddpll pwr analog pll 2.5v power supply. 48 rst# ipu chip reset: active low, minimum of 50s pulse is required pin function 37 rext i external resistor (6.49k) connects to rext and gndrx. 38 vddrcv pwr analog 2.5v power supply. 39 gnd gnd ground 40 tx- o transmit outputs: differential transmit output for 100basetx/fx or 10baset. 41 tx+ o transmit outputs: differential transmit output for fx, 100basetx/fx or 10baset. 42 vddtx pwr transmitter 2.5v power supply. 43 gnd gnd ground. 44 gnd gnd ground. 45 xo o xtal feedback: used with xi for xtal application. 46 xi i crystal oscillator input: input for a crystal or an external 25mhz clock 47 vddpll pwr analog pll 2.5v power supply. 48 rst# ipu chip reset: active low, minimum of 50s pulse is required
march 2006 9 m9999-030106 ks8721b/bt micrel, inc. strapping options (note 1) pin number pin name type (note 2) (note 2) description 6,5, phyad[4:1]/ ipd/o phy address latched at power-up/reset. the default phy address is 00001. 4,3 rxd[0:3] 25 phyad0/ ipu/o int# 9 (3) (3) pcs_lpbk/ ipd/o enables pcs_lpbk mode at power-up/reset. pd (default) = disable, pu = enable. rxdv 11 (3) (3) iso/rxer ipd/o enables isolate mode at power-up/reset. pd (default) = disable, pu = enable. 21 (3) (3) rmii/col ipd/o enables rmii mode at power-up/reset. pd (default) = disable, pu = enable. 22 (3) (3) rmii_btb ipd/o enable rmii_btb mode at power-up/reset. pd (default) = disable, pu = enable. crs 27 spd100/ ipu/o latched into register 0h bit 13 during power-up/reset. pd = 10mbps, pu (default) no fef/ = 100mbps. if spd100 is asserted during power-up/reset, this pin also latched as led1 the speed support in register 4h. (if fxen is pulled up, the latched value 0 means no far_end _fault.) 28 duplex/ ipu/o latched into register 0h bit 8 during power-up/reset. pd = half duplex, pu led2 (default) = full duplex. if duplex is pulled up during reset, this pin also latched as the duplex support in register 4h. 29 nwayen/ ipu/o nway (auto-negotiation) enable. latched into register 0h bit 12 during power-up/ led3 reset. pd = disable auto-negotiation, pu (default) = enable auto-negotiation. 30 pd# ipu power down enable. pu (default) = normal operation, pd = power down mode. note 1. strap-in is latched during power-up or reset. note 2. ipu = input w/ internal pull-up ipd = input w/ internal pull-down ipd/o = input w/ internal pull-down during reset, output pin otherwise ipu/o = input w/ internal pull-up during reset, output pin otherwise pu = strap pin pull-up pd = strap pin pull-down note 3. some devices may drive mii pins that are designated as output (phy) on power up, resulting in incorrect strapping values latched in at reset. it is rcommended that an external pull down via 1k resistor be used in these applications to augment the 8721's internal pull down. 6,5, phyad[4:1]/ ipd/o phy address latched at power-up/reset. the default phy address is 00001. 4,3 rxd[0:3] 25 phyad0/ ipu/o int# 9 rxdv 11 21 22 crs 27 spd100/ ipu/o latched into register 0h bit 13 during power-up/reset. pd = 10mbps, pu (default) no fef/ = 100mbps. if spd100 is asserted during power-up/reset, this pin also latched as led1 the speed support in register 4h. (if fxen is pulled up, the latched value 0 means no far_end _fault.) 28 duplex/ ipu/o latched into register 0h bit 8 during power-up/reset. pd = half duplex, pu led2 (default) = full duplex. if duplex is pulled up during reset, this pin also latched as the duplex support in register 4h. 29 nwayen/ ipu/o nway (auto-negotiation) enable. latched into register 0h bit 12 during power-up/ led3 reset. pd = disable auto-negotiation, pu (default) = enable auto-negotiation. 30 pd# ipu power down enable. pu (default) = normal operation, pd = power down mode. pin number pin name type 6,5, phyad[4:1]/ ipd/o phy address latched at power-up/reset. the default phy address is 00001. 4,3 rxd[0:3] 25 phyad0/ ipu/o int# pcs_lpbk/ ipd/o enables pcs_lpbk mode at power-up/reset. pd (default) = disable, pu = enable. rxdv iso/rxer ipd/o enables isolate mode at power-up/reset. pd (default) = disable, pu = enable. rmii/col ipd/o enables rmii mode at power-up/reset. pd (default) = disable, pu = enable. rmii_btb ipd/o enable rmii_btb mode at power-up/reset. pd (default) = disable, pu = enable. crs 27 spd100/ ipu/o latched into register 0h bit 13 during power-up/reset. pd = 10mbps, pu (default) no fef/ = 100mbps. if spd100 is asserted during power-up/reset, this pin also latched as led1 the speed support in register 4h. (if fxen is pulled up, the latched value 0 means no far_end _fault.) 28 duplex/ ipu/o latched into register 0h bit 8 during power-up/reset. pd = half duplex, pu led2 (default) = full duplex. if duplex is pulled up during reset, this pin also latched as the duplex support in register 4h. 29 nwayen/ ipu/o nway (auto-negotiation) enable. latched into register 0h bit 12 during power-up/ led3 reset. pd = disable auto-negotiation, pu (default) = enable auto-negotiation. 30 pd# ipu power down enable. pu (default) = normal operation, pd = power down mode. pin number pin name type 6,5, phyad[4:1]/ ipd/o phy address latched at power-up/reset. the default phy address is 00001. 4,3 rxd[0:3] 25 phyad0/ ipu/o int# pcs_lpbk/ ipd/o enables pcs_lpbk mode at power-up/reset. pd (default) = disable, pu = enable. rxdv iso/rxer ipd/o enables isolate mode at power-up/reset. pd (default) = disable, pu = enable. rmii/col ipd/o enables rmii mode at power-up/reset. pd (default) = disable, pu = enable. rmii_btb ipd/o enable rmii_btb mode at power-up/reset. pd (default) = disable, pu = enable. 27 spd100/ ipu/o latched into register 0h bit 13 during power-up/reset. pd = 10mbps, pu (default) no fef/ = 100mbps. if spd100 is asserted during power-up/reset, this pin also latched as led1 the speed support in register 4h. (if fxen is pulled up, the latched value 0 means no far_end _fault.) 28 duplex/ ipu/o latched into register 0h bit 8 during power-up/reset. pd = half duplex, pu led2 (default) = full duplex. if duplex is pulled up during reset, this pin also latched as the duplex support in register 4h. 29 nwayen/ ipu/o nway (auto-negotiation) enable. latched into register 0h bit 12 during power-up/ led3 reset. pd = disable auto-negotiation, pu (default) = enable auto-negotiation. 30 pd# ipu power down enable. pu (default) = normal operation, pd = power down mode. description 6,5, phyad[4:1]/ ipd/o phy address latched at power-up/reset. the default phy address is 00001. 4,3 rxd[0:3] pcs_lpbk/ ipd/o enables pcs_lpbk mode at power-up/reset. pd (default) = disable, pu = enable. rxdv iso/rxer ipd/o enables isolate mode at power-up/reset. pd (default) = disable, pu = enable. rmii/col ipd/o enables rmii mode at power-up/reset. pd (default) = disable, pu = enable. rmii_btb ipd/o enable rmii_btb mode at power-up/reset. pd (default) = disable, pu = enable. 27 spd100/ ipu/o latched into register 0h bit 13 during power-up/reset. pd = 10mbps, pu (default) no fef/ = 100mbps. if spd100 is asserted during power-up/reset, this pin also latched as led1 the speed support in register 4h. (if fxen is pulled up, the latched value 0 means no far_end _fault.) 28 duplex/ ipu/o latched into register 0h bit 8 during power-up/reset. pd = half duplex, pu led2 (default) = full duplex. if duplex is pulled up during reset, this pin also latched as the duplex support in register 4h. 29 nwayen/ ipu/o nway (auto-negotiation) enable. latched into register 0h bit 12 during power-up/ led3 reset. pd = disable auto-negotiation, pu (default) = enable auto-negotiation. 30 pd# ipu power down enable. pu (default) = normal operation, pd = power down mode.
ks8721b/bt micrel, inc. m9999-030106 10 march 2006 pin con? guration vddio int#/phyad0 25 24 gnd led0/test 26 23 13 vddc txer txc/ref_clk txen txd0 txd1 txd2 txd3 col/rmii crs/rmii_btb 36 gnd gnd fxsd/fxen rx+ rx- vddrx pd# led3/nwayen led2/duplex led1/spd100 35 34 33 32 31 30 29 28 27 14 15 16 17 18 19 20 21 22 gnd rext 37 12 rxer/iso vddrcv 38 11 1 mdio mdc r3d3/phyad1 rxd2/phyad2 rxd1/phyad3 rxd0/phyad4 vddio gnd rxdv/pcs_lpbk rxc 48 rst# vddpll xi xo gnd gnd vddtx tx+ tx- gnd 47 46 45 44 43 42 41 40 39 2 3 4 5 6 7 8 9 10 48-pin ssop (sm) txd0 txen txc/ref_clk txer vddc txd1 txd2 txd3 mdio mdc rxd3/phyad1 rxd2/phyad2 rxd1/phyad3 rxd0/phyad4 vddio gnd 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 rxdv/pcs_lpbk rxc rxer/iso gnd 9 10 11 12 col/rmii crs/rmii_btb gnd vddio 21 22 23 24 gnd gnd fxsd/fxen rx+ rxC vddrx pd# led3/nwayen 36 35 34 33 32 31 30 29 led2/duplex led1/spd100 led0/test int#/phyad0 28 27 26 25 gnd x0 x1 vddpll rst# gnd vddtx tx+ 48 47 46 45 44 43 42 41 txC gnd vddrcv rext 40 39 38 37 48-pin tqfp (tq)
march 2006 11 m9999-030106 ks8721b/bt micrel, inc. introduction 100basetx transmit the 100basetx transmit function performs parallel to serial conversion, nrz to nrzi conversion, mlt-3 encoding and transmission. the circuitry starts with a parallel to serial conversion, which converts the 25mhz, 4-bit nibbles into a 125 mhz serial bit stream. the incoming data is clocked in at the positive edge of the txc signal. the serialized data is further converted from nrz to nrzi format, and then transmitted in mlt3 current output. the output current is set by an external 1% 6.49k resistor for the 1: 1 transformer ratio. it has a typical rise/fall times of 4 ns and complies to the ansi tp-pmd standard regarding amplitude balance, overshoot and timing jitters. the wave-shaped 10baset output driver is also incor- porated into the 100basetx driver. 100basetx receive the 100basetx receive function performs adaptive equalization, dc restoration, mlt-3 to nrzi conversion, data and clock recovery, nrzi to nrz conversion, and serial to parallel conversion. the receiving side starts with the equalization ? lter to compensate inter-symbol interference (isi) over the twisted pair cable. since the amplitude loss and phase distortion are a function of the length of the cable, the equalizer has to adjust its characteristic to optimize the performance. in this design, the variable equalizer will make an initial estimation based on comparisons of incoming signal strength against some known cable characteristics, then tunes itself for optimization. this is an ongoing process and can self adjust against the environ- mental changes such as temperature variations. the equalized signal then goes through a dc restoration and data conversion block. the dc restoration circuit is used to compensate effect of base line wander and improve the dynamic range. the differential data conversion circuit converts the mlt3 format back to nrzi. the slicing threshold is also adaptive. the clock recovery circuit extracts the 125mhz clock from the edges of the nrzi signal. this recovered clock is then used to convert the nrzi signal into the nrz format. finally, the nrz serial data is converted to 4-bit parallel 4b nibbles. a syn- chronized 25mhz rxc is generated so that the 4b nibbles is clocked out at the negative edge of rck25 and is valid for the receiver at the positive edge. when no valid data is present, the clock recovery circuit is locked to the 25mhz reference clock and both txc and rxc clocks continue to run. pll clock synthesizer the ks8721b/bt generates 125mhz, 25mhz and 20mhz clocks for system timing. an internal crystal oscillator circuit pro- vides the reference clock for the synthesizer. scrambler/de-scrambler (100basetx only) the purpose of the scrambler is to spread the power spectrum of the signal in order to reduce emi and baseline wander . 10baset transmit when txen (transmit enable) goes high, data encoding and transmission will begin. the ks8721b/bt will continue to encode and transmit data as long as txen remains high. the data transmission will end when txen goes low. the last transition occurs at the boundary of the bit cell if the last bit is zero, or at the center of the bit cell if the last bit is one. the output driver is incorporated into the 100base driver to allow transmission with the same magnetics. they are internally wave-shaped and pre-emphasized into outputs with a typical 2.5v amplitude. the harmonic contents are at least 27db below the fundamental when driven by an all-ones manchester-encoded signal. 10baset receive on the receive side, input buffer and level detecting squelch circuits are employed. a differential input receiver circuit and a pll performs the decoding function. the manchester-encoded data stream is separated into clock signal and nrz data. a squelch circuit rejects signals with levels less than 300mv or with short pulse widths in order to prevent noises at the rx+ or rx- input from falsely trigger the decoder. when the input exceeds the squelch limit, the pll locks onto the incoming signal and the ks8721b/bt decodes a data frame. this activates the carrier sense (crs) ad rxdv signals and makes the receive data (rxd) available. the receive clock is maintained active during idle periods in between data reception. sqe and jabber function (10baset only) in 10baset operation, a short pulse will be put out on the col pin after each packet is transmitted. this is required as a test of the 10baset transmit/receive path and is called sqe test. the 10baset transmitter will be disabled and col will go high if txen is high for more than 20ms (jabbering). if txen then goes low for more than 250ms, the 10baset transmitter will be re-enabled and col will go low. auto-negotiation the ks8721b/bt performs auto-negotiation by hardware strapping option (pin 29) or software (register 0.12). it will automati- cally choose its mode of operation by advertising its abilities and comparing them with those received from its link partner whenever auto-negotiation is enabled. it can also be con? gured to advertise 100basetx or 10baset in either full- or half- duplex mode (please refer to auto-negotiation ). the auto-negotiation is disabled in the fx mode.
ks8721b/bt micrel, inc. m9999-030106 12 march 2006 during auto-negotiation, the contents of register 4, coded in fast link pulse (flp), will be sent to its link partner under the conditions of power-on, link-loss or re-start. at the same time, the ks8721b/bt will monitor incoming data to determine its mode of operation. parallel detection circuit will be enabled as soon as either 10baset nlp (normal link pulse) or 100ba- setx idle is detected. the operation mode is con? gured based on the following priority: priority 1: 100basetx, full-duplex priority 2: 100basetx, half-duplex priority 3: 10baset, full-duplex priority 4: 10baset, half-duplex when the ks8721b/bt receives a burst of flp from its link partner with 3 identical link code words (ignoring acknowledge bit), it will store these code words in register 5 and wait for the next 3 identical code words. once the ks8721b/bt detects the second code words, it then con? gures itself according to above-mentioned priority. in addition, the ks8721b/bt also checks 100basetx idle or 10baset nlp symbol. if either is detected, the ks8721b/bt automatically con? gures to match the detected operating speed. mii management interface the ks8721b/bt supports the ieee 802.3 mii management interface, also known as the management data input / output (mdio) interface. this interface allows upper-layer devices to monitor and control the state of the ks8721b/bt. the mdio interface consists of the following: ? a physical connection including a data line (mdio), a clock line (mdc) and an optional interrupt line (intrpt) ? a speci? c protocol that runs across the above-mentioned physical connection and it also allows one controller to communicate with multiple ks8721b/bt devices. each ks8721b/bt assigned an mii address between 0 and 31 by the phyad inputs. ? an internal addressable set of fourteen 16-bit mdio registers. register [0:6] are required and their functions are speci? ed by the ieee 802.3 speci? cations. additional registers are provided for expanded functionality. the intprt pin functions as a management data interrupt in the mii. an active low or high in this pin indicates a status change on the ks8721b/bt based on 1fh.9 level control. register bits at 1bh[15:8] are the interrupt enable bits. register bits at 1bh[7:0] are the interrupt condition bits. this interrupt is cleared by reading register 1bh. mii data interface the data interface consists of separate channels for transmitting data from a 10/100 802.3 compliant media access control- ler (mac) to the ks8721b/bt, and for receiving data from the line. normal data transmission is implemented in 4b nibble mode (4-bit wide nibbles). transmit clock (txc): the transmit clock is normally generated by the ks8721b/bt from an external 25mhz reference source at the x1 input. the transmit data and control signals must always be synchronized to the txc by the mac. the ks8721b/bt normally samples these signals on the rising edge of the txc. receive clock (rxc): for 100basetx links, the receive clock is continuously recovered from the line. if the link goes down, and auto-negotiation is disabled, the receive clock operates off the master input clock (x1 or txc). for 10baset links, the receive clock is recovered from the line while carrier is active, and operates from the master input clock when the line is idle. the ks8721b/bt synchronizes the receive data and control signals on the falling edge of rxc in order to stabilize the signals at the rising edge of the clock with 10ns setup and hold times. transmit enable: the mac must assert txen at the same time as the ? rst nibble of the preamble, and de-assert txen after the last bit of the packet. receive data valid: the ks8721b/bt asserts rxdv when it receives a valid packet. line operating speed and mii mode will determine timing changes in the following way: ? for 100basetx link with the mii in 4b mode, rxdv is asserted from the ? rst nibble of the preamble to the last nibble of the data packet. ? for 10baset links, the entire preamble is truncated. rxdv is asserted with the ? rst nibble of the sfd 5d and remains asserted until the end of the packet. error signals: whenever the ks8721b/bt receives an error symbol from the network, it asserts rxer and drives 1110 (4b) on the rxd pins. when the mac asserts txer, the ks8721b/bt will drive h symbols (a transmit error de? ne in the ieee 802.3 4b/5b code group) out on the line to force signaling errors. carrier sense (crs): for 100tx links, a start-of-stream delimiter, or /j/k symbol pair causes assertion of carrier sense (crs). an end-of-stream delimiter, or /t/r symbol pair causes de-assertion of crs. the pma layer will also de-assert crs if idle symbols are received without /t/r, yet in this case rxer will be asserted for one clock cycle when crs is de-as- serted. for 10t links, crs assertion is based on reception of valid preamble, and de-assertion on reception of an end-of- frame (eof) marker.
march 2006 13 m9999-030106 ks8721b/bt micrel, inc. collision: whenever the line state is half-duplex and the transmitter and receiver are active at the same time, the ks8721b/ bt asserts its collision signal, which is asynchronous to any clock. rmii (reduced mii) data interface rmii interface speci? es a low pin count (reduced) media independent interface (rmii) intended for use between ethernet phys and switch or repeater asics. it is fully compliant with ieee 802.3u [2]. this interface has the following characteristics: ? it is capable of supporting 10mbps and 100mbps data rates. ? a single clock reference is sourced from the mac to phy (or from an external source). ? it provides independent 2-bit wide (di-bit) transmit and receive data paths. ? it uses ttl signal levels, compatible with common digital cmos asic processes. rmii signal de? nition direction direction signal name (w/ respect to the phy) (w/ respect to the mac) use ref_clk input input or output synchronous clock reference for receive, transmit and control interface crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data tx_en input output transit enable txd[1:0] input output transit data rx_er output input (not required) receive error note 1. unused mii signals, txd[3:2], txer need to tie to gnd when rmii is using. reference clock (ref_clk) ref_clk is a continuous 50mhz clock that provides the timing reference for crs_dv, rxd[1:0], tx_en, txd[1:0], and rx_e. ref_clk is sourced by the mac or an external source. switch implementations may choose to provide ref_clk as an input or an output depending on whether they provide a ref_clk output or rely on an external clock distribution device. each phy device shall have an input corresponding to this clock but may use a single clock input for multiple phys implemented on a single ic. carrier sense/receive data valid (crs_dv) crs_dv is asserted asynchronously on detection of carrier due to the criteria relevant to the operating mode. that is, in 10base-t mode, when squelch is passed or in 100base-x mode when 2 non-contiguous zeroes in 10 bits are detected carrier is said to be detected. loss of carrier shall result in the de-assertion of crs_dv synchronous to ref_clk. so long as carrier criteria are being met, crs_dv shall remain asserted continuously from the ? rst recovered di-bit of the frame through the ? nal recovered di- bit and shall be negated prior to the ? rst ref_clk that follows the ? nal di-bit. the data on rxd[1:0] is considered valid once crs_dv is asserted. however, since the assertion of crs_dv is asynchro- nous relative to ref_clk, the data on rxd[1:0] shall be 00 until proper receive signal decoding takes place (see de? nition of rxd[1:0] behavior). receive data [1:0] (rxd[1:0]) rxd[1:0] shall transition synchronously to ref_clk. for each clock period in which crs_dv is asserted, rxd[1:0] transfers two bits of recovered data from the phy. in some cases (e.g. before data recovery or during error conditions) a pre-deter- mined value for rxd[1:0] is transferred instead of recovered data. rxd[1:0] shall be 00 to indicate idle when crs_dv is de-asserted. values of rxd[1:0] other than 00 when crs_dv is de-asserted are reserved for out-of-band signalling (to be de? ned). values other than 00 on rxd[1:0] while crs_dv is de-asserted shall be ignored by the mac/repeater. upon assertion of crs_dv, the phy shall ensure that rxd[1:0]=00 until proper receive decoding takes place. transmit enable (tx_en) transmit enable tx_en indicates that the mac is presenting di-bits on txd[1:0] on the rmii for trans-mission. tx_en shall be asserted synchronously with the ? rst nibble of the preamble and shall remain asserted while all di-bits to be transmitted are presented to the rmii. tx_en shall be negated prior to the ? rst ref_clk following the ? nal di-bit of a frame. tx_en shall transition synchronously with respect to ref_clk. direction direction ref_clk input input or output synchronous clock reference for receive, transmit and control interface crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data tx_en input output transit enable txd[1:0] input output transit data rx_er output input (not required) receive error direction direction (w/ respect to the phy) (w/ respect to the mac) ref_clk input input or output synchronous clock reference for receive, transmit and control interface crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data tx_en input output transit enable txd[1:0] input output transit data rx_er output input (not required) receive error use ref_clk input input or output synchronous clock reference for receive, transmit and control interface crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data tx_en input output transit enable txd[1:0] input output transit data rx_er output input (not required) receive error ref_clk input input or output synchronous clock reference for receive, transmit and signal name ref_clk input input or output synchronous clock reference for receive, transmit and control interface crs_dv output input carrier sense/receive data valid rxd[1:0] output input receive data tx_en input output transit enable txd[1:0] input output transit data rx_er output input (not required) receive error
ks8721b/bt micrel, inc. m9999-030106 14 march 2006 transmit data [1:0] (txd[1:0]) transmit data txd[1:0] shall transition synchronously with respect to ref_clk. when tx_en is asserted, txd[1:0] are accepted for transmission by the phy. txd[1:0] shall be 00 to indicate idle when tx_en is de-asserted. values of txd[1:0] other than 00 when tx_en is de-asserted are reserved for out-of-band signalling (to be de? ned). values other than 00 on txd[1:0] while tx_en is deasserted shall be ignored by the phy. collision detection since the de? nition of crs_dv and tx_en both contain an accurate indication of the start of frame, the mac can reliably regenerate the col signal of the mii by anding tx_en and crs_dv. during the ipg time following the successful transmission of a frame, the col signal is asserted by some transceivers as a self-test. the signal quality error (sqe) function will not be supported by the reduced mii due to the lack of the col signal. historically, sqe was present to indicate that a transceiver located physically remote from the mac was functioning. since the reduced mii only supports chip-to-chip connections on a pcb, sqe functionality is not required. rx_er the phy shall provide rx_er as an output according to the rules speci? ed in ieee 802.3u [2] (see clause 24, figure 24- 11 - receive state diagram). rx_er shall be asserted for one or more ref_clk periods to indicate that an error (e.g. a coding error or any error that a phy is capable of detecting, and that may otherwise be undetectable by the mac sublayer) was detected somewhere in the frame presently being transferred from the phy. rx_er shall transition synchronously with respect to ref_clk. while crs_dv is de-asserted, rx_er shall have no ef fect on the mac. rmii ac characteristics symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % t su txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns t h txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns rising edge rmii transmit timing ref_clk 20 n s t od rxd[1:0] rxd v rxer parameter min typ max units ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns rising edge symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % t t rising edge symbol parameter min typ max units ref_clk frequency 50 mhz ref_clk duty cycle 35 65 % txd[1:0]. tx_en, rxd[1:0], crs_dv, rx_er data set-up to ref_clk rising 4 ns txd[1:0]. tx_en, rxd[1:0], crs_dv, rxer data hold from ref_clk 2 ns parameter min typ max units ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns parameter min typ max units ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns parameter min typ max units ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns parameter min typ max units ref_clk frequency 50 mhz txen, txd[1:0], tx_en, data setup to ref_clk rising edge 4 ns txen, txd[1:0], tx_en, data hold from ref_clk rising edge 2 ns
march 2006 15 m9999-030106 ks8721b/bt micrel, inc. rmii receive timing ref_clk 20 ns tx d[1 : 0] txen txer t 1 t 2 parameter min typ max units ref_clk frequency 50 mhz rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns auto crossover (auto mdi/mdi-x) automatic mdi/mdi-x con? guration is intended to eliminate the need for crossover cables between similar devices. the assignment of pin-outs for a 10/100 base-t crossover function cable is shown below. this feature can eliminate the confusion in real applications so both straight cable and crossover cable can be used. this feature is controlled by register 1f:13. see register 1fhC100basetx phy controller section for details. register 1fhC100basetx phy controller section for details. register 1fhC100basetx phy controller 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 10/100 base-t media dependent interface 10/100 base-t media dependent interface modular connector (rj45) hub (repeater or switch) modular connector (rj45) hub (repeater or switch) receive pair transmit pair receive pair transmit pair figure 1. straight through cable 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 10/100 base-t media dependent interface 10/100 base-t media dependent interface modular connector (rj45) hub (repeater or switch) modular connector (rj45) hub (repeater or switch) receive pair transmit pair receive pair transmit pair figure 2. crossover cable rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns auto crossover (auto mdi/mdi-x) rxd[1:0], crs_dv, rx_er output delay from ref_clk rising edge 2.8 10 ns
ks8721b/bt micrel, inc. m9999-030106 16 march 2006 power management the ks8721b/bt offers the following modes for power management: ? power down mode: this mode can be achieved by writing to register 0.11 or pulling pin 30 pd# low. ? power saving mode: this mode can be disabled by writing to register 1fh.10. the ks8721b/bt will then turn off everything except for the energy detect and pll circuits when the cable is not installed. in other words, the ks8721b/bt will shutdown most of the internal circuits to save power if there is no link. power saving mode will be in his most effective state when auto-negotiation mode is enable. 100bt fx mode 100bt fx mode is activated when fxsd/fxen is higher 0.6v (this pin has a default pull down). under this mode, the auto- negotiation and auto-mdix features are disabled. in ? ber operation fxsd pin should connect to the sd (signal detect) output of the ? ber module. the internal threshold of fxsd is around 1/2 v dd 50mv (1.25v 0.05v). above this level, it is considered ? ber signal detected, and the operation is summarized in the following table: fxsd/fxen condition less than 0.6v 100tx mode less than 1.25v, fx mode but greater than 0.6v no signal detected fef generated greater than 1.25 fx mode signal detected table 1. 100bt fx mode to ensure a proper operation, the swing of ? ber module sd should cover the threshold variation. a resistive voltage divider is recommended to adjust the sd voltage range. fef (far end fault), repetition of a special pattern which consists of 84-one and 1-zero, is generated under fx mode with no signal detected. the purpose of fef is to notify the sender of a faulty link. when receiving a fef, the link will go down to indicate a fault, even with ? ber signal detected. the transmitter does not affect by receiving a fef and still sends out its normal transmit pattern from mac. fef can be disabled by strapping pin 27 low . refer to strapping options section. strapping options section. strapping options media converter operation ks8721b/bt is capable of performing media conversion with 2 parts in a back to back rmii loop-back mode as indicated in the diagram. both parts are in rmii mode and with rmii btb asserted (pin 21 and 22 strapped high). one part is operating at tx mode and the other in fx mode. both parts can share a common 50mhz oscillator. under this operation, auto-negotiation on the tx side will prohibit 10baset link up. txd2, active high, can disable transmit- ter and set it at tri-state. rxd2 serves as energy detection can indicate if there is line signal detected. txd3 should tied low and rxd3 let ? oat. please contact micrel fae for application note. ks8721 b rx +/ - tx +/- ftx fr x ks8721 b vcc pi n 34 rxd txd to t he s d pin of the fiber module (fiber mode) vcc rx d txd 21 22 pi n pi n 21 22 osc 50 m h z txc / ref _clk txc/ ref_c lk figure 3. fiber module fxsd/fxen condition less than 0.6v 100tx mode less than 1.25v, fx mode but greater than 0.6v no signal detected fef generated greater than 1.25 fx mode signal detected fxsd/fxen condition less than 0.6v 100tx mode less than 1.25v, fx mode but greater than 0.6v no signal detected fef generated greater than 1.25 fx mode signal detected
march 2006 17 m9999-030106 ks8721b/bt micrel, inc. register map register no. description 0h basic control register 1h basic status register 2h phy identi? er i 3h phy identi? er ii 4h auto-negotiation advertisement register 5h auto-negotiation link partner ability register 6h auto-negotiation expansion register 7h auto-negotiation next page register 8h link partner next page ability 15h rxer counter register 1bh interrupt control/status register 1fh 100basetx phy control register address name description mode (note 1) default register 0h - basic control 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.11 power down 1 = power down mode; 0 = normal operation rw 0 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0 = normal operation 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0 = normal operation. bit is self-clearing 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 transmitter 1 = disable transmitter register 1h - basic status 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 0 = not capable of 100basex full duplex 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 0 = not capable of 100basex half duplex 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 0 = no 10mbps with full duplex capability 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1 0 = no 10mbps with half duplex capability note 1. rw: read/write, ro: read only, sc: self clear, lh: latch high, ll: latch low. some of the default values are set by strap-in. see srap- ping options. register 0h - basic control 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0 = normal operation 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0 = normal operation. bit is self-clearing 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 transmitter 1 = disable transmitter register 1h - basic status 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 0 = not capable of 100basex full duplex 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 0 = not capable of 100basex half duplex 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 0 = no 10mbps with full duplex capability 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1 0 = no 10mbps with half duplex capability 0h basic control register 1h basic status register 2h phy identi? er i 3h phy identi? er ii 4h auto-negotiation advertisement register 5h auto-negotiation link partner ability register 6h auto-negotiation expansion register 7h auto-negotiation next page register 8h link partner next page ability 15h rxer counter register 1bh interrupt control/status register 1fh 100basetx phy control register register no. description 0h basic control register 1h basic status register 2h phy identi? er i 3h phy identi? er ii 4h auto-negotiation advertisement register 5h auto-negotiation link partner ability register 6h auto-negotiation expansion register 7h auto-negotiation next page register 8h link partner next page ability 15h rxer counter register 1bh interrupt control/status register 1fh 100basetx phy control register address name description mode default address name description mode 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.11 power down 1 = power down mode; 0 = normal operation rw 0 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0 = normal operation 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0 = normal operation. bit is self-clearing 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 transmitter 1 = disable transmitter 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.11 power down 1 = power down mode; 0 = normal operation rw 0 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0 = normal operation. bit is self-clearing 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.11 power down 1 = power down mode; 0 = normal operation rw 0 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0 = normal operation 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0 = normal operation. bit is self-clearing 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 transmitter 1 = disable transmitter 0.15 reset 1 = software reset. bit is self-clearing rw/sc 0 0.14 loop-back 1 = loop-back mode; 0 = normal operation rw 0 0.13 speed select (lsb) 1 = 100mbps; 0 = 10mbps rw set by ignored if auto-negotiation is enabled (0.12 = 1) spd100 0.12 auto-negotiation enable 1 = enable auto-negotiation process (override 0.13 and 0.8) rw set by 0 = disable auto-negotiation process nwayen 0.11 power down 1 = power down mode; 0 = normal operation rw 0 0.10 isolate 1 = electrical isolation of phy from mii and tx+/tx- rw set by iso 0.9 restart auto-negotiation 1 = restart auto-negotiation process rw/sc 0 0.8 duplex mode 1 = full duplex; 0 = half duplex rw set by duplex 0.7 collision test 1 = enable col test; 0 = disable col test rw 0 0.6:1 reserved ro 0 0.0 disable 0 = enable transmitter r/w 0 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 0 = not capable of 100basex full duplex 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 0 = not capable of 100basex half duplex 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 0 = no 10mbps with full duplex capability 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1 0 = no 10mbps with half duplex capability 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 0 = not capable of 100basex full duplex 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 0 = not capable of 100basex half duplex 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 0 = no 10mbps with full duplex capability 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1 0 = no 10mbps with half duplex capability 1.15 100baset4 1 = t4 capable; 0 = not t4 capable ro 0 1.14 100basetx full duplex 1 = capable of 100basex full duplex ro 1 1.13 100basetx half duplex 1 = capable of 100basex half duplex ro 1 1.12 10baset full duplex 1 = 10mbps with full duplex ro 1 1.11 10baset half duplex 1 = 10mbps with half duplex ro 1
ks8721b/bt micrel, inc. m9999-030106 18 march 2006 address name description mode (note 1) default 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 0 = auto-negotiation process not completed 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 0 = unable to perform auto-negotiation 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 register 2h - phy identi? er 1 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h unique identi? er (oui). micrels oui is 0010a1 (hex) register 3h - phy identi? er 2 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro 000101 unique identi? er (oui). micrels oui is 0010a1 (hex) 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 register 4h - auto-negotiation advertisement 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 register 5h - auto-negotiation link partner ability 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 5.14 acknowledge 1 = link code word received from partner 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0 note 1. rw: read/write, ro: read only, sc: self clear, lh: latch high, ll: latch low. some of the default values are set by strap-in. see srap- ping options. address name description mode 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 0 = auto-negotiation process not completed 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 0 = unable to perform auto-negotiation 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 address name description mode 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 address name description mode 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 0 = auto-negotiation process not completed 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 0 = unable to perform auto-negotiation 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 default 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 1.10:7 reserved ro 0 1.6 no preamble 1 = preamble suppression; 0 = normal preamble ro 1 1.5 auto-negotiation complete 1 = auto-negotiation process completed ro 0 0 = auto-negotiation process not completed 1.4 remote fault 1 = remote fault; 0 = no remote fault ro/lh 0 1.3 auto-negotiation ability 1 = capable to perform auto-negotiation ro 1 0 = unable to perform auto-negotiation 1.2 link status 1 = link is up; 0 = link is down ro/ll 0 1.1 jabber detect 1 = jabber detected; 0 = jabber not detected. default is low ro/lh 0 1.0 extended capability 1 = supports extended capabilities registers ro 1 register 2h - phy identi? er 1 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h unique identi? er (oui). micrels oui is 0010a1 (hex) 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro 000101 unique identi? er (oui). micrels oui is 0010a1 (hex) 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 register 5h - auto-negotiation link partner ability 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 5.14 acknowledge 1 = link code word received from partner 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h unique identi? er (oui). micrels oui is 0010a1 (hex) 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h unique identi? er (oui). micrels oui is 0010a1 (hex) 2.15:0 phy id number assigned to the 3rd through 18th bits of the organizationally ro 0022h 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro unique identi? er (oui). micrels oui is 0010a1 (hex) 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro unique identi? er (oui). micrels oui is 0010a1 (hex) 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 3.15:10 phy id number assigned to the 19th through 24th bits of the organizationally ro 3.9:4 model number six bit manufacturers model number ro 100001 3.3:0 revision number four bit manufacturers model number ro 1001 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 4.15 next page 1 = next page capable; 0 = no next page capability. rw 0 4.14 reserved ro 0 4.13 remote fault 1 = remote fault supported; 0 = no remote fault rw 0 4.12 : 11 reserved ro 0 4.10 pause 1 = pause function supported; 0 = no pause function rw 0 4.9 100baset4 1 = t4 capable; 0 = no t4 capability ro 0 4.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability rw set by spd100 & duplex 4.7 100basetx 1 = tx capable; 0 = no tx capability rw set by spd100 4.6 10baset full duplex 1 = 10mbps with full duplex rw set by 0 = no 10mbps full duplex capability duplex 4.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability rw 1 4.4:0 selector field [00001] = ieee 802.3 rw 00001 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 5.14 acknowledge 1 = link code word received from partner 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 5.14 acknowledge 1 = link code word received from partner 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0 5.15 next page 1 = next page capable; 0 = no next page capability ro 0 0 = link code word not yet received ro 0 5.13 remote fault 1 = remote fault detected; 0 = no remote fault ro 0 5.12 reserved ro 0
march 2006 19 m9999-030106 ks8721b/bt micrel, inc. address name description mode (note 1) default 5.11:10 pause 5.10 5 .11 ro 0 0 0 no pause 0 1 asymmetric pause (link partner) asymmetric pause (link partner) 1 0 symmetric pause symmetric pause 1 1 symmetric & asymmetric pause (local device) symmetric & asymmetric pause (local device) 5.9 100 baset4 1 = t4 capable; 0 = no t4 capability ro 0 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 0 = no 10mbps full duplex capability 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 register 6h - auto-negotiation expansion 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 0 = no fault detected by parallel detection. 6.3 link partner next 1 = link partner has next page capability ro 0 page able 0 = link partner does not have next page capability 6.2 next page able 1 = local device has next page capability ro 1 0 = local device does not have next page capability 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 auto-negotiation able 0 = link partner does not have auto-negotiation capability register 7h - auto-negotiation next page 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 0 = cannot comply with message 7.11 toggle 1 = previous value of the transmitted link code word ro 0 equaled logic one; 0 = logic zero 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 register 8h - link partner next page ability 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 0 = no successful receipt of link word 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 0 = not able to act on the information 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 to logic zero; 0 = previous value of transmitted link code word equal to logic one 8.10:0 message field ro 0 note 1. rw: read/write, ro: read only, sc: self clear, lh: latch high, ll: latch low. some of the default values are set by strap-in. see srap- ping options. address name description mode 5.11:10 pause 5.10 5 .11 ro 0 0 0 0 1 1 0 1 1 5.9 100 baset4 1 = t4 capable; 0 = no t4 capability ro 0 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 0 = no 10mbps full duplex capability 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 address name description mode 5.11:10 pause 5.10 5 .11 ro 0 5.9 100 baset4 1 = t4 capable; 0 = no t4 capability ro 0 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 address name description mode 5.11:10 pause 5.10 5 .11 ro 0 0 0 0 1 1 0 1 1 5.9 100 baset4 1 = t4 capable; 0 = no t4 capability ro 0 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 0 = no 10mbps full duplex capability 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 default 5.11:10 pause 5.10 5 .11 ro 0 5.9 100 baset4 1 = t4 capable; 0 = no t4 capability ro 0 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 0 = no fault detected by parallel detection. page able 0 = link partner does not have next page capability 6.2 next page able 1 = local device has next page capability ro 1 0 = local device does not have next page capability 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 auto-negotiation able 0 = link partner does not have auto-negotiation capability 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 1 = link partner has next page capability ro 0 6.2 next page able 1 = local device has next page capability ro 1 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 0 = no fault detected by parallel detection. 1 = link partner has next page capability ro 0 page able 0 = link partner does not have next page capability 6.2 next page able 1 = local device has next page capability ro 1 0 = local device does not have next page capability 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 auto-negotiation able 0 = link partner does not have auto-negotiation capability 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 1 = link partner has next page capability ro 0 6.2 next page able 1 = local device has next page capability ro 1 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 0 = cannot comply with message 7.11 toggle 1 = previous value of the transmitted link code word ro 0 equaled logic one; 0 = logic zero 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 7.11 toggle 1 = previous value of the transmitted link code word ro 0 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 0 = cannot comply with message 7.11 toggle 1 = previous value of the transmitted link code word ro 0 equaled logic one; 0 = logic zero 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 7.11 toggle 1 = previous value of the transmitted link code word ro 0 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 5.11:10 pause 5.10 5 .11 ro 0 0 0 0 1 1 0 1 1 5.8 100basetx full duplex 1 = tx with full duplex; 0 = no tx full duplex capability ro 0 5.7 100basetx 1 = tx capable; 0 = no tx capability ro 0 5.6 10baset full duplex 1 = 10mbps with full duplex ro 0 0 = no 10mbps full duplex capability 5.5 10baset 1 = 10mbps capable; 0 = no 10mbps capability ro 0 5.4:0 selector field [00001] = ieee 802.3 ro 00001 6.15:5 reserved ro 0 6.4 parallel detection fault 1 = fault detected by parallel detection ro/lh 0 0 = no fault detected by parallel detection. 6.3 page able 0 = link partner does not have next page capability 6.2 next page able 1 = local device has next page capability ro 1 0 = local device does not have next page capability 6.1 page received 1 = new page received; 0 = new page not yet received ro/lh 0 6.0 link partner 1 = link partner has auto-negotiation capability ro 0 auto-negotiation able 0 = link partner does not have auto-negotiation capability 7.15 next page 1 = additional next page(s) will follow; 0 = last page rw 0 7.14 reserved ro 0 7.13 message page 1 = message page; 0 = unformatted page rw 1 7.12 acknowledge2 1 = will comply with message rw 0 0 = cannot comply with message 7.11 toggle 1 = previous value of the transmitted link code word ro 0 equaled logic one; 0 = logic zero 7.10:0 message field 11-bit wide ? eld to encode 2048 messages rw 001 register 8h - link partner next page ability 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 0 = no successful receipt of link word 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 0 = not able to act on the information 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 to logic zero; 0 = previous value of transmitted link code word equal to logic one 8.10:0 message field ro 0 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 0 = no successful receipt of link word 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 0 = not able to act on the information 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 to logic zero; 0 = previous value of transmitted link code word equal to logic one 8.10:0 message field ro 0 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 8.10:0 message field ro 0 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 0 = no successful receipt of link word 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 0 = not able to act on the information 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 to logic zero; 0 = previous value of transmitted link code word equal to logic one 8.10:0 message field ro 0 8.15 next page 1 = additional next page(s) will follow; 0 = last page ro 0 8.14 acknowledge 1 = successful receipt of link word ro 0 8.13 message page 1 = message page; 0 = unformatted page ro 0 8.12 acknowledge2 1 = able to act on the information ro 0 8.11 toggle 1 = previous value of transmitted link code word equal ro 0 8.10:0 message field ro 0
ks8721b/bt micrel, inc. m9999-030106 20 march 2006 address name description mode (note 1) default register 15h - rxer counter 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 register 1bh - interrupt control/status register 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 interrupt enable 0 = disable receive error interrupt 1b.13 page received 1 = enable page received interrupt rw 0 interrupt enable 0 = disable page received interrupt 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 interrupt enable 0 = disable parallel detect fault interrupt 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 interrupt enable 0 = disable link partner acknowledge interrupt 1b.10 link down 1 = enable link down interrupt rw 0 interrupt enable 0 = disable link down interrupt 1b.9 remote fault 1 = enable remote fault interrupt rw 0 interrupt enable 0 = disable remote fault interrupt 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 0 = disable link up interrupt 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 0 = jabber interrupt does not occurred 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 0 = receive error does not occurred 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 0 = page receive does not occurred 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 fault interrupt 0 = parallel detect fault does not occurred 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 acknowledge interrupt 0 = link partner acknowledge does not occurred 1b.2 link down interrupt 1 = link down occurred ro/sc 0 0 = link down does not occurred 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 0 = remote fault does not occurred 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0 0 = link up interrupt does not occurred register 1fh - 100basetx phy controller 1f.15:14 reserved 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 0 = no signal setected on rx+/- 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 this bit bypasses the control logic and allow transmitter to send pattern even if there is no link. 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 note 1. rw: read/write, ro: read only, sc: self clear, lh: latch high, ll: latch low. some of the default values are set by strap-in. see srap- ping options. address name description mode address name description mode address name description mode default 1f.15:14 reserved 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 0 = no signal setected on rx+/- 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 to send pattern even if there is no link. 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 0 = no signal setected on rx+/- 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 to send pattern even if there is no link. 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 register 15h - rxer counter 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 register 1bh - interrupt control/status register 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 interrupt enable 0 = disable receive error interrupt 1b.13 page received 1 = enable page received interrupt rw 0 interrupt enable 0 = disable page received interrupt 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 interrupt enable 0 = disable parallel detect fault interrupt 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 interrupt enable 0 = disable link partner acknowledge interrupt 1b.10 link down 1 = enable link down interrupt rw 0 interrupt enable 0 = disable link down interrupt 1b.9 remote fault 1 = enable remote fault interrupt rw 0 interrupt enable 0 = disable remote fault interrupt 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 0 = disable link up interrupt 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 0 = jabber interrupt does not occurred 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 0 = receive error does not occurred 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 0 = page receive does not occurred 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 fault interrupt 0 = parallel detect fault does not occurred 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 acknowledge interrupt 0 = link partner acknowledge does not occurred 1b.2 link down interrupt 1 = link down occurred ro/sc 0 0 = link down does not occurred 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 0 = remote fault does not occurred 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0 0 = link up interrupt does not occurred 1f.15:14 reserved 1f:13 pairswap disable 1 = disable mdi/mdix; 0 = enable mdi/mdix r/w 0 1f.12 energy detect 1 = presence of signal on rx+/- analog wire pair ro 0 0 = no signal setected on rx+/- 1f.11 force link 1 = force link pass; 0 = normal link operation r/w 0 to send pattern even if there is no link. 1f.10 power saving 1 = enable ppower saving; 0 = disable rw 1 1f.9 interrupt level 1 = interrupt pin active high; 0 = active low rw 0 1f.8 enable jabber 1 = enable jabber counter; 0 = disable rw 1 1f.7 auto-negotiation complete 1 = auto-negotiation complete; 0 = not nomplete rw 0 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 15.15:0 rxer counter rx error counter for the rx_er in each package ro 0000 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 interrupt enable 0 = disable receive error interrupt 1b.13 page received 1 = enable page received interrupt rw 0 interrupt enable 0 = disable page received interrupt 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 interrupt enable 0 = disable parallel detect fault interrupt 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 interrupt enable 0 = disable link partner acknowledge interrupt 1b.10 link down 1 = enable link down interrupt rw 0 interrupt enable 0 = disable link down interrupt 1b.9 remote fault 1 = enable remote fault interrupt rw 0 interrupt enable 0 = disable remote fault interrupt 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 0 = disable link up interrupt 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 0 = jabber interrupt does not occurred 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 0 = receive error does not occurred 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 0 = page receive does not occurred 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 fault interrupt 0 = parallel detect fault does not occurred 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 acknowledge interrupt 0 = link partner acknowledge does not occurred 1b.2 link down interrupt 1 = link down occurred ro/sc 0 0 = link down does not occurred 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 0 = remote fault does not occurred 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0 0 = link up interrupt does not occurred 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 1b.13 page received 1 = enable page received interrupt rw 0 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 1b.10 link down 1 = enable link down interrupt rw 0 1b.9 remote fault 1 = enable remote fault interrupt rw 0 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 1b.2 link down interrupt 1 = link down occurred ro/sc 0 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 interrupt enable 0 = disable receive error interrupt 1b.13 page received 1 = enable page received interrupt rw 0 interrupt enable 0 = disable page received interrupt 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 interrupt enable 0 = disable parallel detect fault interrupt 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 interrupt enable 0 = disable link partner acknowledge interrupt 1b.10 link down 1 = enable link down interrupt rw 0 interrupt enable 0 = disable link down interrupt 1b.9 remote fault 1 = enable remote fault interrupt rw 0 interrupt enable 0 = disable remote fault interrupt 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 0 = disable link up interrupt 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 0 = jabber interrupt does not occurred 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 0 = receive error does not occurred 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 0 = page receive does not occurred 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 fault interrupt 0 = parallel detect fault does not occurred 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 acknowledge interrupt 0 = link partner acknowledge does not occurred 1b.2 link down interrupt 1 = link down occurred ro/sc 0 0 = link down does not occurred 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 0 = remote fault does not occurred 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0 0 = link up interrupt does not occurred 1b.15 jabber interrupt enable 1 = enable jabber interrupt; 0=disable jabber interrupt rw 0 1b.14 receive error 1 = enable receive error interrupt rw 0 1b.13 page received 1 = enable page received interrupt rw 0 1b.12 parallel detect fault 1 = enable parallel detect fault interrupt rw 0 1b.11 link partner acknowledge 1 = enable link partner acknowledge interrupt rw 0 1b.10 link down 1 = enable link down interrupt rw 0 1b.9 remote fault 1 = enable remote fault interrupt rw 0 1b.8 link up interrupt enable 1 = enable link up interrupt rw 0 1b.7 jabber interrupt 1 = jabber interrupt occurred ro/sc 0 1b.6 receive error interrupt 1 = receive error occurred ro/sc 0 1b.5 page receive interrupt 1 = page receive occurred ro/sc 0 1b.4 parallel detect 1 = parallel detect fault occurred ro/sc 0 1b.3 link partner 1 = link partner acknowledge occurred ro/sc 0 1b.2 link down interrupt 1 = link down occurred ro/sc 0 1b.1 remote fault interrupt 1 = remote fault occurred ro/sc 0 1b.0 link up interrupt 1 = link up interrupt occurred ro/sc 0
march 2006 21 m9999-030106 ks8721b/bt micrel, inc. address name description mode (note 1) default 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 (flow-control result) 1f.5 phy isolate 1 = phy in isolate mode; 0 = not isolated ro 0 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 [001] = 10baset half duplex [010] = 100basetx half duplex [011] = reserved [101] = 10baset full duplex [110] = 100basetx full duplex [111] = phy/mii isolate 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0 note 1. rw: read/write, ro: read only, sc : self clear, lh: latch high, ll: latch low. some of the default values are set by strap-in. see strap- ping options. address name description mode 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 (flow-control result) 1f.5 phy isolate 1 = phy in isolate mode; 0 = not isolated ro 0 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 [001] = 10baset half duplex [010] = 100basetx half duplex [011] = reserved [101] = 10baset full duplex [110] = 100basetx full duplex [111] = phy/mii isolate 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0 address name description mode 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 1f.5 phy isolate 1 = phy in isolate mode; 0 = not isolated ro 0 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0 address name description mode 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 1f.5 phy isolate 1 = phy in isolate mode; 0 = not isolated ro 0 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 [001] = 10baset half duplex [010] = 100basetx half duplex [011] = reserved [101] = 10baset full duplex [110] = 100basetx full duplex [111] = phy/mii isolate 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0 default 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 1f.5 phy isolate 1 = phy in isolate mode; 0 = not isolated ro 0 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0 1f.6 enable pause 1 = ? ow control capable; 0 = no ? ow control ro 0 (flow-control result) 1f.4:2 operation mode indication [000] = still in auto-negotiation ro 0 [001] = 10baset half duplex [010] = 100basetx half duplex [011] = reserved [101] = 10baset full duplex [110] = 100basetx full duplex [111] = phy/mii isolate 1f.1 enable sqe test 1 = enable sqe test; 0 = disable rw 0 1f.0 disable data scrambling 1 = disable scrambler; 0 = enable rw 0
ks8721b/bt micrel, inc. m9999-030106 22 march 2006 absolute maximum ratings (note 1) supply voltage (v ddc , v dd_pll , v dd_tx , v dd_rcv , v dd_rx ) .................................................... C0.5v to +3.0v (v dd_rx (v dd_rx ddio ) dd_rx ) dd_rx ...................................................... C0.5v to +4.0v input voltage ................................................ C0.5v to +4.0v output voltage .............................................. C0.5v to +4.0v lead temperature (soldering, 10 sec.) ...................... 270c storage temperature (t s ) ........................ C55c to +150c operating ratings (note 2) supply voltage (v ddc , v dd_pll , v dd_tx , v dd_rcv , v dd_rx ) ........................................... +2.375v to +2.625v (v dd_rx (v dd_rx ddio ) dd_rx ) dd_rx ................ +2.375v to +2.625v or +3.0v to +3.6v ambient temperature (t a ambient temperature (t a ambient temperature (t ) ............................ C0c to +70c package thermal resistance (note 3) tqfp ( ja ) ................................................................... 69.64c/w ssop ( ja ) ................................................................. 42.91c/w electrical characteristics (note 4) v dd = 2.5v 5%; t a = 2.5v 5%; t a = 2.5v 5%; t = 0c to +70c; unless noted; a = 0c to +70c; unless noted; a bold values indicate C40c t a values indicate C40c t a values indicate C40c t +85c; unless noted. a +85c; unless noted. a symbol parameter condition min typ max units total supply current (including tx output driver current) i dd1 normal 100basetx 107 ma i dd2 normal 10baset (50% utilization) 144 ma i dd3 power saving mode 100basetx 47 ma i dd5 power down mode 4 ma ttl inputs v ih input high voltage v dd (i/o) v C0.8 v il input low voltage 0.8 v i in input current v in = gnd ~ v dd C10 10 a ttl outputs v oh output high voltage i oh = C4ma v dd (i/o) v C0.4 v ol output low voltage i ol = 4ma 0.4 v |i oz | output tr-state leakage 10 a 100basetx receive r in rx+/rxC differential input 8 k resistance propagation delay from magnetics to rdtx 50 110 ns 100basetx transmit (measured differentially after 1:1 transformer) v o peak differential output voltage 50 from each output to v dd 0.95 1.05 v v imb output voltage imbalance 50 from each output to v dd 2 % t r , t t rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns 100basetx transmit (measured differentially after 1:1 transformer) duty cycle distortion 0.5 v overshoot 5 % v set reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 ns (pk-pk note 1. exceeding the absolute maximum rating may damage the device. note 2. the device is not guaranteed to function outside its operating rating. unused inputs must always be tied to an appropriate logic voltage level (ground to v dd ). note 3. no hs (heat spreader) in package. note 4. speci? cation for packaged product only. symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units normal 100basetx 107 ma normal 100basetx 107 ma normal 10baset (50% utilization) 144 ma power saving mode 100basetx 47 ma power down mode 4 ma normal 100basetx 107 ma normal 10baset (50% utilization) 144 ma power saving mode 100basetx 47 ma power down mode 4 ma normal 100basetx 107 ma normal 10baset (50% utilization) 144 ma power saving mode 100basetx 47 ma power down mode 4 ma normal 100basetx 107 ma normal 10baset (50% utilization) 144 ma power saving mode 100basetx 47 ma power down mode 4 ma normal 100basetx 107 ma normal 10baset (50% utilization) 144 ma power saving mode 100basetx 47 ma power down mode 4 ma input high voltage v input high voltage v input low voltage 0.8 v input current v input high voltage v input low voltage 0.8 v C10 10 a C0.8 input low voltage 0.8 v C10 10 a C0.8 input low voltage 0.8 v C10 10 a input low voltage 0.8 v C10 10 a output high voltage i output high voltage i output low voltage i output tr-state leakage 10 a = C4ma v = 4ma 0.4 v output tr-state leakage 10 a = 4ma 0.4 v output tr-state leakage 10 a = 4ma 0.4 v output tr-state leakage 10 a = 4ma 0.4 v output tr-state leakage 10 a resistance rx+/rxC differential input 8 k propagation delay from magnetics to rdtx 50 110 ns rx+/rxC differential input 8 k propagation delay from magnetics to rdtx 50 110 ns rx+/rxC differential input 8 k propagation delay from magnetics to rdtx 50 110 ns rx+/rxC differential input 8 k propagation delay from magnetics to rdtx 50 110 ns rx+/rxC differential input 8 k propagation delay from magnetics to rdtx 50 110 ns peak differential output voltage 50 from each output to v rise/fall time imbalance 0 0.5 ns peak differential output voltage 50 from each output to v output voltage imbalance 50 from each output to v rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns 0.95 1.05 v 2 % rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns 0.95 1.05 v 2 % rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns 0.95 1.05 v 2 % rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns 0.95 1.05 v 2 % rise/fall time 3 5 ns rise/fall time imbalance 0 0.5 ns duty cycle distortion 0.5 v propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 duty cycle distortion 0.5 v overshoot 5 % reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 duty cycle distortion 0.5 v overshoot 5 % reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 duty cycle distortion 0.5 v overshoot 5 % reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 duty cycle distortion 0.5 v overshoot 5 % reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns jitters 0.7 1.4 duty cycle distortion 0.5 v overshoot 5 % reference voltage of iset 0.75 ns propagation delay from tdtx to magentics 45 60 ns
march 2006 23 m9999-030106 ks8721b/bt micrel, inc. symbol parameter condition min typ max units 10basetx receive r in rx+/rxC differential 8 k input resistance v sq squelch threshold 5mhz square wave 400 mv 10basetx transmit (measured differentially after 1:1 transformer) v p peak differential output voltage 50 from each output to v dd 2.2 2.8 v jitters added 50 from each output to v dd 3.5 ns t r , t t rise/fall time 25 ns clock outputs x1, x2 crystal oscillator 25 mhz rxc 100 receive clock, 100tx 25 mhz rxc 10 receive clock, 10t 2.5 mhz receive clock jitters 3.0 ns (pk-pk) txc 100 transmit clock, 100tx 25 mhz txc 10 transmit clock, 10t 2.5 mhz transmit clock jitters 1.8 ns (pk-pk) symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units symbol parameter condition min typ max units input resistance rx+/rxC differential 8 k input resistance squelch threshold 5mhz square wave 400 mv rx+/rxC differential 8 k input resistance squelch threshold 5mhz square wave 400 mv rx+/rxC differential 8 k squelch threshold 5mhz square wave 400 mv rx+/rxC differential 8 k squelch threshold 5mhz square wave 400 mv rx+/rxC differential 8 k squelch threshold 5mhz square wave 400 mv peak differential output voltage 50 from each output to v peak differential output voltage 50 from each output to v jitters added 50 from each output to v rise/fall time 25 ns 2.2 2.8 v 3.5 ns rise/fall time 25 ns 2.2 2.8 v 3.5 ns rise/fall time 25 ns 2.2 2.8 v 3.5 ns rise/fall time 25 ns 2.2 2.8 v 3.5 ns rise/fall time 25 ns x1, x2 crystal oscillator 25 mhz transmit clock jitters 1.8 x1, x2 crystal oscillator 25 mhz receive clock, 100tx 25 mhz receive clock, 10t 2.5 mhz receive clock jitters 3.0 transmit clock, 100tx 25 mhz transmit clock, 10t 2.5 mhz transmit clock jitters 1.8 x1, x2 crystal oscillator 25 mhz receive clock, 100tx 25 mhz receive clock, 10t 2.5 mhz receive clock jitters 3.0 transmit clock, 100tx 25 mhz transmit clock, 10t 2.5 mhz transmit clock jitters 1.8 x1, x2 crystal oscillator 25 mhz receive clock, 100tx 25 mhz receive clock, 10t 2.5 mhz receive clock jitters 3.0 transmit clock, 100tx 25 mhz transmit clock, 10t 2.5 mhz transmit clock jitters 1.8 x1, x2 crystal oscillator 25 mhz receive clock, 100tx 25 mhz receive clock, 10t 2.5 mhz receive clock jitters 3.0 transmit clock, 100tx 25 mhz transmit clock, 10t 2.5 mhz transmit clock jitters 1.8 x1, x2 crystal oscillator 25 mhz receive clock, 100tx 25 mhz receive clock, 10t 2.5 mhz transmit clock, 100tx 25 mhz transmit clock, 10t 2.5 mhz
ks8721b/bt micrel, inc. m9999-030106 24 march 2006 timing diagrams txc t hd2 t su2 txen txd[3 :0] t su1 t hd1 crs t cr s2 t crs1 txp/t x m t la t valid data txc t sqe col t sqep s qe timi ng txen figure 4. 10baset mii transmit timing symbol parameter symbol parameter min typ max units min typ max units min typ max units min typ max units t su1 txd [3:0] set-up to txc high 10 ns txd [3:0] set-up to txc high 10 ns txd [3:0] set-up to txc high 10 ns txd [3:0] set-up to txc high 10 ns txd [3:0] set-up to txc high 10 ns txd [3:0] set-up to txc high 10 ns t su2 txen set-up to txc high 10 ns txen set-up to txc high 10 ns txen set-up to txc high 10 ns txen set-up to txc high 10 ns txen set-up to txc high 10 ns txen set-up to txc high 10 ns t hd1 txd [3:0] hold after txc high 0 ns txd [3:0] hold after txc high 0 ns txd [3:0] hold after txc high 0 ns txd [3:0] hold after txc high 0 ns txd [3:0] hold after txc high 0 ns txd [3:0] hold after txc high 0 ns t hd2 txen hold after txc high 0 ns txen hold after txc high 0 ns txen hold after txc high 0 ns txen hold after txc high 0 ns txen hold after txc high 0 ns txen hold after txc high 0 ns t crs1 txen high to crs asserted latency 4 bt txen high to crs asserted latency 4 bt txen high to crs asserted latency 4 bt txen high to crs asserted latency 4 bt txen high to crs asserted latency 4 bt txen high to crs asserted latency 4 bt t crs2 txen low to crs de-asserted latency 8 bt txen low to crs de-asserted latency 8 bt txen low to crs de-asserted latency 8 bt txen low to crs de-asserted latency 8 bt txen low to crs de-asserted latency 8 bt txen low to crs de-asserted latency 8 bt t lat txen high to txp/txm output (tx latency) 4 bt txen high to txp/txm output (tx latency) 4 bt txen high to txp/txm output (tx latency) 4 bt txen high to txp/txm output (tx latency) 4 bt txen high to txp/txm output (tx latency) 4 bt txen high to txp/txm output (tx latency) 4 bt t sqe col (sqe) delay aftter txen ae-asserted 2.5 s col (sqe) delay aftter txen ae-asserted 2.5 s col (sqe) delay aftter txen ae-asserted 2.5 s col (sqe) delay aftter txen ae-asserted 2.5 s col (sqe) delay aftter txen ae-asserted 2.5 s col (sqe) delay aftter txen ae-asserted 2.5 s t sqep col (sqe) pulse duration 1.0 s col (sqe) pulse duration 1.0 s col (sqe) pulse duration 1.0 s col (sqe) pulse duration 1.0 s col (sqe) pulse duration 1.0 s col (sqe) pulse duration 1.0 s table 2. 10baset mii transmit timing parameters
march 2006 25 m9999-030106 ks8721b/bt micrel, inc. txc t su2 txe n t hd2 t x d[ 3: 0] , txe r t su1 cr s t cr s2 t c rs 1 tx+/ tx- t la t symb o l ou t da t a in t hd1 figure 5. 100baset mii transmit timing symbol parameter min typ max units t su1 txd [3:0] set-up to txc high 10 ns t su2 txen set-up to txc high 10 ns t hd1 txd [3:0] hold after txc high 0 ns t hd2 txer hold after txc high 0 ns t hd3 txen hold after txc high 0 ns t crs1 txen high to crs asserted latency 4 bt t crs2 txen low to crs de-asserted latency 4 bt t lat txen high to tx+/txC output (tx latency) 9 bt table 3. 100baset mii transmit timing parameters symbol parameter txd [3:0] set-up to txc high 10 ns txen set-up to txc high 10 ns txd [3:0] hold after txc high 0 ns txer hold after txc high 0 ns txen hold after txc high 0 ns txen high to crs asserted latency 4 bt txen low to crs de-asserted latency 4 bt txen high to tx+/txC output (tx latency) 9 bt txd [3:0] set-up to txc high 10 ns txen set-up to txc high 10 ns txd [3:0] hold after txc high 0 ns txer hold after txc high 0 ns txen hold after txc high 0 ns txen high to crs asserted latency 4 bt txen low to crs de-asserted latency 4 bt txen high to tx+/txC output (tx latency) 9 bt min typ max units txd [3:0] set-up to txc high 10 ns txen set-up to txc high 10 ns txd [3:0] hold after txc high 0 ns txer hold after txc high 0 ns txen hold after txc high 0 ns txen high to crs asserted latency 4 bt txen low to crs de-asserted latency 4 bt txen high to tx+/txC output (tx latency) 9 bt min typ max units txd [3:0] set-up to txc high 10 ns txen set-up to txc high 10 ns txd [3:0] hold after txc high 0 ns txer hold after txc high 0 ns txen hold after txc high 0 ns txen high to crs asserted latency 4 bt txen low to crs de-asserted latency 4 bt txen high to tx+/txC output (tx latency) 9 bt min typ max units txd [3:0] set-up to txc high 10 ns txen set-up to txc high 10 ns txd [3:0] hold after txc high 0 ns txer hold after txc high 0 ns txen hold after txc high 0 ns txen high to crs asserted latency 4 bt txen low to crs de-asserted latency 4 bt txen high to tx+/txC output (tx latency) 9 bt
ks8721b/bt micrel, inc. m9999-030106 26 march 2006 r x + / rx - r x d [ 3: 0] rx e r cr s t crs1 t crs 2 rx d v t rl a t t su t hd st a r t o f st r e a m e n d of st r e a m rx c t wl t wh t p figure 6. 100baset mii receivce timing symbol parameter min typ max units t p rxc period 40 ns t wl rxc pulse width 20 ns wl rxc pulse width 20 ns wl t wh rxc pulse width 20 ns t su rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns t hd rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns t rlat crs to rxd latency, 4b or 5b aligned 6 bt t crs1 start of stream to csr asserted 106 138 ns t crs2 end of stream to csr de-asserted 154 186 ns table 4. 100baset mii receive timing parameters symbol parameter rxc period 40 ns rxc pulse width 20 ns rxc pulse width 20 ns rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns crs to rxd latency, 4b or 5b aligned 6 bt start of stream to csr asserted 106 138 ns end of stream to csr de-asserted 154 186 ns rxc period 40 ns rxc pulse width 20 ns rxc pulse width 20 ns rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns crs to rxd latency, 4b or 5b aligned 6 bt start of stream to csr asserted 106 138 ns end of stream to csr de-asserted 154 186 ns min typ max units rxc period 40 ns rxc pulse width 20 ns rxc pulse width 20 ns rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns crs to rxd latency, 4b or 5b aligned 6 bt start of stream to csr asserted 106 138 ns end of stream to csr de-asserted 154 186 ns min typ max units rxc period 40 ns rxc pulse width 20 ns rxc pulse width 20 ns rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns crs to rxd latency, 4b or 5b aligned 6 bt start of stream to csr asserted 106 138 ns end of stream to csr de-asserted 154 186 ns min typ max units rxc period 40 ns rxc pulse width 20 ns rxc pulse width 20 ns rxd [3:0], rxer, rxdv set-up to rising edge of rxc 20 ns rxd [3:0], rxer, rxdv hold from rising edge of rxc 20 ns crs to rxd latency, 4b or 5b aligned 6 bt start of stream to csr asserted 106 138 ns end of stream to csr de-asserted 154 186 ns
march 2006 27 m9999-030106 ks8721b/bt micrel, inc. t pw tx+/ tx- cl ock pul s e data puls e cl o c k pulse t pw t ct d t c tc t flp w t b tb tx+/ tx- da t a pulse flp bu r s t flp bu rs t figure 7. auto-negotiation/fast link pulse timing symbol parameter min typ max units t btb flp burst to flp burst 8 16 24 ms t flpw flp burst width 2 ms t pw clock/data pulse width 100 ns t ctd clock pulse to data pulse 69 s t ctc clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s table 5. auto-negotiation/fast link pulse timing symbol parameter flp burst to flp burst 8 16 24 ms flp burst width 2 ms clock/data pulse width 100 ns clock pulse to data pulse 69 s clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s flp burst to flp burst 8 16 24 ms flp burst width 2 ms clock/data pulse width 100 ns clock pulse to data pulse 69 s clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s min typ max units flp burst to flp burst 8 16 24 ms flp burst width 2 ms clock/data pulse width 100 ns clock pulse to data pulse 69 s clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s min typ max units flp burst to flp burst 8 16 24 ms flp burst width 2 ms clock/data pulse width 100 ns clock pulse to data pulse 69 s clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s min typ max units flp burst to flp burst 8 16 24 ms flp burst width 2 ms clock/data pulse width 100 ns clock pulse to data pulse 69 s clock pulse to clock pulse 136 s number of clock/data pulses per burst 17 33 s
ks8721b/bt micrel, inc. m9999-030106 28 march 2006 t md1 va l i d da t a mdi o (in t o ch ip) vali d data mdc t md2 mdi o (ou t of c h ip ) vali d data t md3 t p figure 8. serial management interface t iming symbol parameter min typ max units t p mdc period 400 ns t md1 mdio set-up to mdc (mdio as input) 10 ns t md2 mdio hold after mdc (mdio as input) 10 ns t md3 mdc to mdio valid (mdio as output) 222 ns table 6. serial management interface timing symbol parameter mdc period 400 ns mdio set-up to mdc (mdio as input) 10 ns mdio hold after mdc (mdio as input) 10 ns mdc to mdio valid (mdio as output) 222 ns mdc period 400 ns mdio set-up to mdc (mdio as input) 10 ns mdio hold after mdc (mdio as input) 10 ns mdc to mdio valid (mdio as output) 222 ns min typ max units mdc period 400 ns mdio set-up to mdc (mdio as input) 10 ns mdio hold after mdc (mdio as input) 10 ns mdc to mdio valid (mdio as output) 222 ns min typ max units mdc period 400 ns mdio set-up to mdc (mdio as input) 10 ns mdio hold after mdc (mdio as input) 10 ns mdc to mdio valid (mdio as output) 222 ns min typ max units mdc period 400 ns mdio set-up to mdc (mdio as input) 10 ns mdio hold after mdc (mdio as input) 10 ns mdc to mdio valid (mdio as output) 222 ns
march 2006 29 m9999-030106 ks8721b/bt micrel, inc. ts r tc s t c h trc su pp l y vo l t a g e rst _ n str a p - in va l u e s t ra p- i n / out p ut p i n figure 9. reset t iming symbol parameter min typ max units t sr stable supply voltages to reset high 10 ms sr stable supply v oltages to reset high 10 ms sr t cs con? guration set-up time 50 ns t ch con? guration hold time 50 ns t rc reset to strap-in pin output 50 s table 7. reset timing parameters reset circuit diagram micrel recommendeds the following discrete reset circuit as shown in figure 10 when powering up the ks8721b/bt device. for the application where the reset circuit signal comes from another device (e.g., cpu, fpga, etc), we recommend the reset circuit as shown in figure 11. vcc r 10k d2 c 10f d1 cpu/fpga rst_out_n ks8721b/bt rst d1, d2: 1n4148 figure 10. recommended reset circuit. vcc r 10k c 10f d1 ks8721b/bt rst d1: 1n4148 figure 11. recommended circuit for interfacing with cpu/fpga reset at power-on-reset, r, c, and d1 provide the necessary ramp rise time to reset the micrel device. the reset out from cpu/ fpga provides warm reset after power up. it is also recommended to power up the vdd core voltage earlier than vddio voltage. at worst case, the both vdd core and vddio voltages should come up at the same time. symbol parameter stable supply voltages to reset high 10 ms con? guration set-up time 50 ns con? guration hold time 50 ns reset to strap-in pin output 50 s stable supply voltages to reset high 10 ms con? guration set-up time 50 ns con? guration hold time 50 ns reset to strap-in pin output 50 s min typ max units stable supply voltages to reset high 10 ms con? guration set-up time 50 ns con? guration hold time 50 ns reset to strap-in pin output 50 s min typ max units stable supply voltages to reset high 10 ms con? guration set-up time 50 ns con? guration hold time 50 ns reset to strap-in pin output 50 s min typ max units stable supply voltages to reset high 10 ms con? guration set-up time 50 ns con? guration hold time 50 ns reset to strap-in pin output 50 s
ks8721b/bt micrel, inc. m9999-030106 30 march 2006 selection of isolation transformer (note 1) one simple 1:1 isolation transformer is needed at the line interface. an isolation transformer with integrated common-mode choke is recommended for exceeding fcc requirements. the following table gives recommended transformer character- istics. characteristics name value test condition turns ratio 1 ct : 1 ct open-circuit inductance (min.) 350h 100mv, 100 khz, 8 ma leakage inductance (max.) 0.4h 1mhz (min.) inter-winding capacitance (max.) 12pf d.c. resistance (max.) 0.9 insertion loss (max.) 1.0db 0mhz to 65mhz hipot (min.) 1500vrms note 1. the ieee 802.3u standard for 100basetx assumes a transformer loss of 0.5db. for the transmit line transformer, insertion loss of up to 1.3db can be compensated by increasing the line drive current by means of reducing the iset resistor value. selection of reference crystal an oscillator or crystal with the following typical characteristics is recommended. characteristics name value units frequency 25.00000 mhz frequency tolerance (max.) 100 ppm load capacitance (max.) 20 pf series resistance (max.) 40 frequency tolerance (max.) 100 ppm load capacitance (max.) 20 pf series resistance (max.) 40 characteristics name value units frequency 25.00000 mhz frequency tolerance (max.) 100 ppm load capacitance (max.) 20 pf series resistance (max.) 40 characteristics name value units frequency 25.00000 mhz frequency tolerance (max.) 100 ppm load capacitance (max.) 20 pf series resistance (max.) 40 open-circuit inductance (min.) 350h 100mv, 100 khz, 8 ma leakage inductance (max.) 0.4h 1mhz (min.) inter-winding capacitance (max.) 12pf d.c. resistance (max.) 0.9 insertion loss (max.) 1.0db 0mhz to 65mhz hipot (min.) 1500vrms characteristics name value test condition turns ratio 1 ct : 1 ct open-circuit inductance (min.) 350h 100mv, 100 khz, 8 ma leakage inductance (max.) 0.4h 1mhz (min.) inter-winding capacitance (max.) 12pf d.c. resistance (max.) 0.9 insertion loss (max.) 1.0db 0mhz to 65mhz hipot (min.) 1500vrms characteristics name value test condition open-circuit inductance (min.) 350h 100mv, 100 khz, 8 ma leakage inductance (max.) 0.4h 1mhz (min.) insertion loss (max.) 1.0db 0mhz to 65mhz single port number magnetic manufacturer part number auto mdix of ports pulse h1102 yes 1 bel fuse s558-5999-u7 yes 1 ycl pt163020 yes 1 transpower hb726 yes 1 delta lf8505 yes 1 lankom lf-h41s yes 1 integrated transformers pulse j0011d21 yes 1 pulse j00-0061 yes 1 table 8. quali? ed transformer lists single port number magnetic manufacturer part number auto mdix of ports pulse h1102 yes 1 bel fuse s558-5999-u7 yes 1 ycl pt163020 yes 1 transpower hb726 yes 1 delta lf8505 yes 1 lankom lf-h41s yes 1 pulse j0011d21 yes 1 pulse j00-0061 yes 1 single port number magnetic manufacturer part number auto mdix of ports pulse h1102 yes 1 bel fuse s558-5999-u7 yes 1 ycl pt163020 yes 1 transpower hb726 yes 1 delta lf8505 yes 1 lankom lf-h41s yes 1 single port number magnetic manufacturer part number auto mdix of ports pulse h1102 yes 1 bel fuse s558-5999-u7 yes 1 ycl pt163020 yes 1 transpower hb726 yes 1 delta lf8505 yes 1 lankom lf-h41s yes 1 single port number magnetic manufacturer part number auto mdix of ports pulse h1102 yes 1 bel fuse s558-5999-u7 yes 1 ycl pt163020 yes 1 transpower hb726 yes 1 delta lf8505 yes 1 lankom lf-h41s yes 1 pulse j0011d21 yes 1 pulse j00-0061 yes 1 pulse j0011d21 yes 1 pulse j00-0061 yes 1 pulse j0011d21 yes 1 pulse j00-0061 yes 1
march 2006 31 m9999-030106 ks8721b/bt micrel, inc. package information 48-pin ssop (sm)
ks8721b/bt micrel, inc. m9999-030106 32 march 2006 48-pin tqfp (tq) micrel inc. 2180 fortune drive san jose, ca 95131 usa tel + 1 (408) 944-0800 fax + 1 (408) 474-1000 web http://www.micrel.com this information furnished by micrel in this data sheet is believed to be accurate and reliable. however no responsibility is assumed by micrel for its use. micrel reserves the right to change circuitry and speci? cations at any time without noti? cation to the customer. micrel products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a signi? cant injury to the user. a purchasers use or sale of micrel products for use in life support appliances, devices or systems is a purchaser s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2002 micrel, incorporated.

▲Up To Search▲

Price & Availability of KS8721B11

	To Download KS8721B11 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .